![]() |
![]() |
'03 z400, '87 Lt250R Quadracer, '01 Lt80, '96 Lt80
The radiator on this bike is aluminum but somebody in its past decided to spray paint it black. Today I decided to drain and pull the radiator so I can strip the paint off of it and try to polish it up a bit. I used airplane stripper to get paint off
7C1FAF43-2D55-472B-BA60-20FF036207E0-2087-000003FAC61C4581.jpg
I didn't know the fins were dented and bent so bad until I stripped the black paint off. I'm going to try to straighten them the best I can then start polishing.
'03 z400, '87 Lt250R Quadracer, '01 Lt80, '96 Lt80
i bought used Walsh rad and when it got to me almost all the fins on one side was flat. it took me 3 nights in front of the TV with 2 really small flat head screw drivers to get it all straight. take your time. you can make it looking like new again.
good job on the build BTW. i like to check in here from time to time to check your progess.
Looking good Dan... keep at it!
2009 LTZ400 EFI
2009 KingQuad 500 Axi Power Steering
1992 Quadracer LT250r... full resto..SOLD
1989 Quadzilla
1988 Quadracer LT250r... Parting out
2011 Ski Doo MXZ 600 E-tec
1987 trx250r... resto. coming soon
bike came out really good. I just picked up an 86 with a spare engine for 250$.Im pretty stoked and would appricate any advice you have to offer.
86 Quadracer
94 ktm 440
03 gsxr
Good looking quad! I have a chance to get my hands on one! Just wondering about a value? A guy offered to trade me for my 99 400ex! Not really interested on another quad! But figured I would do a little research! It's suppose to be really fast port and polished a couple more things done! Really just need to know how much I could get out of it? Thanks in advance
After straightening all the fins on my old radiator, I somehow caused a leak. Instead of messing with it anymore, I just got a new one off eBay.
4B1602D4-742D-4CFF-9F3F-1417E32759DE-1158-00000208CEC6D8D4.jpg
'03 z400, '87 Lt250R Quadracer, '01 Lt80, '96 Lt80
I just got another goodie for this ole bike.
25DFAD3B-7CA6-4847-8DF9-D1E312B4CDFE-5912-00000E407C06ABE1_zps82c3c6c3.JPG
D9ACFB3A-3C33-4438-A4F4-1D974B3F683F-5912-00000E407D3CF63E_zpsd6bc1892.JPG
I scored it off Craigslist for $60 bucks. Can't wait to get it installed
'03 z400, '87 Lt250R Quadracer, '01 Lt80, '96 Lt80
I got the factory headlight cleaned up, powdercoated, and installed today
5E0AC37C-FACF-4DF8-88E0-FC760581DA60-6072-00000E4668662B28_zps2c1f061a.jpg
0FDDAC81-CD05-4946-B725-E5005028E18C-6072-00000E4670C17682_zpsc7dc43d0.jpg
47DDD30F-336A-44BF-A6F5-5481839371AE-6072-00000E465CBDF3D2_zpsea1a3f22.jpg
'03 z400, '87 Lt250R Quadracer, '01 Lt80, '96 Lt80
I can't believe, with how far I tore this bike apart, that I didn't know until now it had tapered carrier bearings.
They weren't sloppy until now so I didn't mess with them. I had a extra set of single row carrier bearings and seals from my z400 that was going to install. What a surprise when I slid that axle out and popped the seals.
I'm glad though because I think they have alot more load rating
'03 z400, '87 Lt250R Quadracer, '01 Lt80, '96 Lt80