I have a 2011 Raptor 700, She max`s out at 125 kmh, I am gonna start moding the sheet out of it but I want to remove the governor so I am not limited to one speed....I hear you gotta cut a wire or something,,, any help?
I have a 2011 Raptor 700, She max`s out at 125 kmh, I am gonna start moding the sheet out of it but I want to remove the governor so I am not limited to one speed....I hear you gotta cut a wire or something,,, any help?
2011 Raptor 700R
2007 Suzuki RMZ 250
There's is a lot of good info on them @ modder raptor.com you can change the coil wire and it will gain 1 hp....
cut the baby blue wire and ground it to the frame.... your good to go
01 Raptor 686R
lonestar +3a-arms- +2 swinger/ axcaliber+3/ elka's
hmf full system-K&N filters
GYTR full skids-shift lever- brake lever
yukon tranny-one way starter bearing
686 wiseco
cam, oil, speed limiter mods
3 spark plug head, high vilocity ported, stage 3 cam, maier plastics, gusseted PC'd frame,
05 Ram reg cab short box
and a shed full of other toys
I hate to see people cutting wires.....get the dynatek ignition witch raises it to 9100 ish or get the new MSD ignition where you set it. by the way it is a rev limiter not a speed limiter. More than likely you are running out of power to overcome wind resistance and such to push past that speed.
734 09 Raptor
Meglodon by Bo,KW springs, Web 4 Cam, 54mm TB, 105.5mm CP cylinder, 12:1 CP,Barkers Inframe,Dynatek Coil,PC V,Dynatek Programable ignition,CCP stabilizer,+5 swinger,Boss Noss Sys, Direct Drive Lock-up, KDS Evac valve,HID Light conversion,SPAL fan
Tuned by EHS Racing 73hp 51Tq
07 LT-R450
Athena 500cc Kit
Porting by Bo
DMC Pro Comp 4
PCIII
Trinity intake
ATP intake Cam
Tuned by EHS 50hp 34Tq
85 ATC 250r...restoration I/P.
no its a top speed limiter. the 660's amd 700's both have them, on the 660 you have to remove a little gear and grind every other tooth off to the sensor dets an inaccurate reading, amd on the 700 its the blue wire that runs from the cpu to the final drive shaft of the trannyOriginally posted by 09RappySe
I hate to see people cutting wires.....get the dynatek ignition witch raises it to 9100 ish or get the new MSD ignition where you set it. by the way it is a rev limiter not a speed limiter. More than likely you are running out of power to overcome wind resistance and such to push past that speed.
01 Raptor 686R
lonestar +3a-arms- +2 swinger/ axcaliber+3/ elka's
hmf full system-K&N filters
GYTR full skids-shift lever- brake lever
yukon tranny-one way starter bearing
686 wiseco
cam, oil, speed limiter mods
3 spark plug head, high vilocity ported, stage 3 cam, maier plastics, gusseted PC'd frame,
05 Ram reg cab short box
and a shed full of other toys
I believe he knows that, its a 5th gear timing retard. Cutting the blue wire and grounding it disables it but the Dynatek or MSD will do away with the speed limiter and raise the rev limiter some without hacking the harness.
13:1 105mm CP
Ported head
Monster Duals
Texas Quad intake
PCIII
Extreme Fabrication nerfs
MSR CR High Bend bars
2.5" extended stock stem
ASV levers
15t/36T Renthal sprocket
Gusseted frame
Gforce axle
Full Flight A-arms
Holeshot MXR6 tires
68rwhp/55rwtq on knobbies
but that costs 350 bucks more.....and increasing the rev limiter on a big bore quad is usless and dangerous. they stop making power long before the rev limiter.
01 Raptor 686R
lonestar +3a-arms- +2 swinger/ axcaliber+3/ elka's
hmf full system-K&N filters
GYTR full skids-shift lever- brake lever
yukon tranny-one way starter bearing
686 wiseco
cam, oil, speed limiter mods
3 spark plug head, high vilocity ported, stage 3 cam, maier plastics, gusseted PC'd frame,
05 Ram reg cab short box
and a shed full of other toys
Well, thats not even the reason why people buy them. The rev limiter isnt an issue until you get into .500"+ lift cams and +3 TI valved porting gets into the mix. The main reason why to buy one is to be able to have an adjustable timing system and secondary reason is the 5th gear limiter. If you just wanna to do away with the limiter sure, just ground the wire but the more you internally mod your bike the more you will benifit from tuning the timing. Just think how much power could be added if you adjusted the timing on this build:
13:1 105mm CP
Ported head
Monster Duals
Texas Quad intake
PCIII
Extreme Fabrication nerfs
MSR CR High Bend bars
2.5" extended stock stem
ASV levers
15t/36T Renthal sprocket
Gusseted frame
Gforce axle
Full Flight A-arms
Holeshot MXR6 tires
68rwhp/55rwtq on knobbies