Results 1 to 10 of 10

Thread: Our typhoon done up!

  1. #1
    Join Date
    Dec 2005
    Posts
    186

    Our typhoon done up!











  2. #2
    Join Date
    Aug 2005
    Location
    Winter Haven, Fl.
    Posts
    2,005
    Looking good! Your rear looks like it's too high in the air. Any way you can lower the rear and what is your length from the footpeg to the ground? May look that way because the front is still low due to the stock arms. Has he had a chance to ride it? Looks like that rear will be nice and cush now .
    If it'll run... I'm ridin'!!!

    http://home.earthlink.net/~hotscott03/

    Sons:
    Jhamir "JAM" Scott #320
    KX85

    Sponsors:
    Firepower Minis Motors
    Pirelli
    Artistic Apparel
    Smith Optics
    Athena
    DeCal Works
    PitPosse
    AGV Helmets
    Signs A Rama (Lakeland)
    ASV Inventions
    Dirtyfoot Adventures
    O'Neal USA
    TwinAir
    OneNation Extreme
    R1R Performance
    C4 Suspension

  3. #3
    Join Date
    Mar 2008
    Posts
    18
    how much did that rear frame support cost? the part that holds the axle and rear shock. Not sure what its called but my daughters is already broke at the weld. Two months of riding and she weighs 60 lbs.

  4. #4
    Join Date
    Dec 2005
    Posts
    186
    Rob its like 8 inches to the bottom of the footpeg from the ground . When my son sits on it it sags out like 3" ......This bike has way more travel than before ....BIG DIFF....!!!!

    we will be out at the track on friday ill lat you know how it dose.




    Flip out .......are you taking about the swingarm or the sub frame?

  5. #5
    Join Date
    Aug 2005
    Location
    Winter Haven, Fl.
    Posts
    2,005
    I think it's more that your front still sits so low. Your rear seems to be about where ours is now. Maybe a 1/2 inch higher but like you said it'll come down some due to rider sag. I'm also confused on what Flipout was asking about (may be the swing arm).
    If it'll run... I'm ridin'!!!

    http://home.earthlink.net/~hotscott03/

    Sons:
    Jhamir "JAM" Scott #320
    KX85

    Sponsors:
    Firepower Minis Motors
    Pirelli
    Artistic Apparel
    Smith Optics
    Athena
    DeCal Works
    PitPosse
    AGV Helmets
    Signs A Rama (Lakeland)
    ASV Inventions
    Dirtyfoot Adventures
    O'Neal USA
    TwinAir
    OneNation Extreme
    R1R Performance
    C4 Suspension

  6. #6
    Join Date
    Mar 2008
    Posts
    18
    swing arm. My daughters is already cracking at the weld towards the top. Im gonna have this welded again, but im def wanting to buy one of those new fab swing arms. How much. My daughter is tiny, im supprised the original is breaking.

  7. #7
    Join Date
    Aug 2005
    Location
    Winter Haven, Fl.
    Posts
    2,005
    It's because of the rear support being in the wrong place. Give Lew (ChassisInc) a call 503-318-1710. I ordered one and ours should be here next week.

    Sand, get some vids of your boys upcoming race.
    If it'll run... I'm ridin'!!!

    http://home.earthlink.net/~hotscott03/

    Sons:
    Jhamir "JAM" Scott #320
    KX85

    Sponsors:
    Firepower Minis Motors
    Pirelli
    Artistic Apparel
    Smith Optics
    Athena
    DeCal Works
    PitPosse
    AGV Helmets
    Signs A Rama (Lakeland)
    ASV Inventions
    Dirtyfoot Adventures
    O'Neal USA
    TwinAir
    OneNation Extreme
    R1R Performance
    C4 Suspension

  8. #8
    Join Date
    Apr 2002
    Location
    mass
    Posts
    1,163

    i like the stem

    how much was it ? i sent them an email but never heard back ...thanks,mike

  9. #9
    Join Date
    Apr 2009
    Posts
    106

    Nice Ride

    it turned out very nice.
    Russ & Cade Jenkins
    Cade Jenkins Racing
    253-677-0237
    www.cadejenkinsracing.com
    Email: russ@aaglassnation.com
    Email: cade@cadejenkinsracing.com


    XTREME Flat Track Team
    Sponsor’s:
    AA Glass Nation Inc.
    TBOLTUSA.com
    Indoor Comfort Systems Inc
    Quality Brake and Muffler
    Hot Shots Photos
    Bartle's Welding
    Larsen Sign Company
    The Line Up Custom Printing and Trophies
    QRC Karts
    PMI Powder Coating 253-539-3339
    ELKA SUPENSION


    http://i831.photobucket.com/albums/z...hhgZM-X3-1.jpg

  10. #10
    Join Date
    May 2017
    Posts
    2
    what bracket did you use for the top of the rear shock

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •