Results 1 to 4 of 4

Thread: 2004 DVX 440 Race ready 20 Grand invested

  1. #1
    Join Date
    Jun 2010
    Location
    Coon Rapids MN
    Posts
    6

    2004 DVX 440 Race ready 20 Grand invested

    Great Starter quad for someone begining in the 450 classes. I literally have 20 Grand invested into this quad, I am asking 5 grand, if I were to part it out I would get that easily, I dont want to part it out, but I will if the higher value items go first (ex. Shocks, aarms, swing arm, carb). I'm the original owner of this quad, I drove it off the show room floor in 2004. I also have all the stock parts for this machine that will go with it. I would trade for an LTR if someone was interested and it wasnt roached out. Here is a list of the aftermarkets from front bumper to rear grab bar.

    AC racing bumper (powder coated black)
    (front) ITP Baja wheels, ITP Quad cross tires
    Lonestar Hubs (powder coated Green)
    White Roll Design +2 long travel AArms
    Alba brake line clamps (powder coated green)
    Streamline +2 stainless steel braided brake lines
    Roll Design HD Tie Rods
    Steering Knuckles powder coated green
    Headlight removed, tail light removed, light controls removed from the bars, reverse removed, key removed, temp/rev/N light cluster removed and rewired for push button start
    Black headlight cover held in with safety wire
    Motowoz long travel triple rate shocks with piggy back rezzies, fully rebound and compression adjustable. These shocks are the only ones like it on the planet, They were custom made and colored for me from Motowoz
    Houser steering stem (Black) with Anti Vibe bar clamps (powder coated white)
    MSR Bars
    Moose Racing Clutch Perch
    Moose Racing thumb throttle
    Moose Racing Front Brake Master cylinder cover
    Edelbrock throttle cable
    ODI Lock on grips
    Green Vent tube for gas cap
    Oil Tank Powder coated white
    UM black nerfs
    Motor mounts powder coated white
    Athena 440 Big Bore kit
    Hinson Clutch Basket
    Barnett Dirt Digger Clutch Kit
    Edelbrock Carb
    K&N Aluminum intake
    UNI Dual Stage Oil Wetted foam air filter
    red anodized timing inspection cap and red anodized Crank Hole plug
    Yoshimura RS-2 Comp series full stainless Exhaust
    Green CV4 Hoses
    Black Verde gripper seat cover
    (Plastics) New Black center section cut in half for easy removal, New Green fenders
    Custom Graphics from Blown Concepts
    Frame and Sub Frame Powder Coated Green
    AC Racing Skid Plate
    Alba Case saver and Block Off Plate
    Lonestar Racing Hollow swing arm pivot Bolt
    Alba Swing Arm powder coated white from black
    Motowoz rear Long travel with remote rezzie, fully compression and rebound adjustable
    Elka Linkage
    Green rear Streamline stainless steel braided brake line
    DID 520 ATV Chain
    T.M. Design works chain guide
    Titax front and rear sprocket (powder coated white)
    Streamline Rotors
    DuraBlue Eliminator +2 Triple chromed Axle
    LoneStar Racing hubs (powder coated green) and Locking nuts on Axle
    AC Racing Grab Bar W/number plate (powder coated black)
    Douglas Yellow Label bead lock rear wheels with ITP Quad cross Tires
    Yoshimura Mud Plugs in the wheels
    Attached Images Attached Images
    • File Type: jpg 1.jpg (89.4 KB, 186 views)

  2. #2
    Join Date
    Jun 2010
    Location
    Coon Rapids MN
    Posts
    6

    front

    the front end
    Attached Images Attached Images
    • File Type: jpg 3.jpg (88.0 KB, 168 views)

  3. #3
    Join Date
    Jun 2010
    Location
    Coon Rapids MN
    Posts
    6
    the rear end
    Attached Images Attached Images
    • File Type: jpg 4.jpg (90.8 KB, 149 views)

  4. #4
    Join Date
    Jun 2010
    Location
    Coon Rapids MN
    Posts
    6
    sprocket view
    Attached Images Attached Images
    • File Type: jpg 6.jpg (74.5 KB, 151 views)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •