Is it safe to polish my quads engine with Never-Dull? What do you guys use?
Is it safe to polish my quads engine with Never-Dull? What do you guys use?
Honda TRX300EX
Honda Recon 250 ~ Sold
Honda Rancher 350
Built Ford Tough
i wouldnt see why it would hurt.
05 450r
Houser stem, Denton Stabalizer, Moose Fatbars, Baldwin Hot Start Cable, Hot Rod Crank, Moose Billit Clutch Basket, Moose Easy Pull Clutch Lever, pro motion twist throttle, Lonestar Carrier, Blingstar Heel Guards, Pced Fame(Black), Pced subframe(Black), Pced swinger(Black), PRM chassis Skid, Maier Hood, front hipers
04 tld pred
Full hmf sport pipe, pro taper bars, um nerfs, itp rims, pced frame and subframe and a-arms ( orange), pced swing arm shock springs and steering stem (black), cycra handguards, motion pro twist throttle, ims bumper, dg grab bar, moose chassis and swinger skids, spyder grips, k&n filter, pro design kill switch, front itp t9 beadlocks, rear douglas ultimate beadlocks
I didn't know if the engine has a special coating on it or something that the never-dull would take off.
Honda TRX300EX
Honda Recon 250 ~ Sold
Honda Rancher 350
Built Ford Tough
i dont think it does i clean mine all the time
05 450r
Houser stem, Denton Stabalizer, Moose Fatbars, Baldwin Hot Start Cable, Hot Rod Crank, Moose Billit Clutch Basket, Moose Easy Pull Clutch Lever, pro motion twist throttle, Lonestar Carrier, Blingstar Heel Guards, Pced Fame(Black), Pced subframe(Black), Pced swinger(Black), PRM chassis Skid, Maier Hood, front hipers
04 tld pred
Full hmf sport pipe, pro taper bars, um nerfs, itp rims, pced frame and subframe and a-arms ( orange), pced swing arm shock springs and steering stem (black), cycra handguards, motion pro twist throttle, ims bumper, dg grab bar, moose chassis and swinger skids, spyder grips, k&n filter, pro design kill switch, front itp t9 beadlocks, rear douglas ultimate beadlocks
With never-dull?Originally posted by ride red 14
i dont think it does i clean mine all the time
Honda TRX300EX
Honda Recon 250 ~ Sold
Honda Rancher 350
Built Ford Tough
Why don't you try it and tell us how it works out.
Scott Landgraf
1989 Honda 250r
-Mild port-FMF Header Pipe-FMF Silencer-CR250 Head Gasket-Coolhead-Rad Valve-K&N Filter-DuraBlue Axle-Works Shocks-Lonestar Steering Stem-Renthal Bars
Thank you Wes and Andy
SOLD! Gone but not forgotten.
2002 300ex (yellow) with
PRM bottom frame skid plate
My Drifter
1985 5.0 Mustang GT
-5-speed
I don't want to hurt it lol.Originally posted by Scott-300ex
Why don't you try it and tell us how it works out.
Honda TRX300EX
Honda Recon 250 ~ Sold
Honda Rancher 350
Built Ford Tough
it will work,,,alot of people use acid based solvents on there engine and it works fine...
personally i just use soapy water and steel wool..
Country Boy Can Survive
-97 F150-
400EX frame up build in the future.
i use that exact same stuff for my frame. i highly doubt it'll do anything for your motor. buy some good, quality engine degreaser and use that. it'll have a greater effect.
heres a pic of my frame...
BIKELESS...
Long sigs are a waste, please keep them short, we don't need to know what quad your buddy, dad, brother, mother, aunt, uncle, and the neighbors cat is riding, or the mods that they have, want, have ordered, looked at, thought about or sold.
Never Dull is fine to use. Be careful with any type of engine cleaner/degreaser. We went riding one day, stopped to wash them at a friend's house. He swore by this "Castrol SuperClean" stuff. I had never used it before. Won't use again. It left some pretty bad streaks on my side covers that won't come out.
God must love stupid people; He made so many.