i just got a 02' 300ex and was wondering how to know if it has a jet kit or not?i got from an atv seller and he just sells them,he dont know what they have and dont have.
i just got a 02' 300ex and was wondering how to know if it has a jet kit or not?i got from an atv seller and he just sells them,he dont know what they have and dont have.
take the carb apart, located under the gas tank, look at the main jets and see wat size they are. look at the needle
Well if it has stock exhaust, and filter and all it should be a stock main, and pilot.....stock is 122 main / 38 pilot.
Why is this important to you? Does it run alright? Rich or lean?
MY TOYS
406X Honda
Powroll stroker w/ Vesrah shorty rod
ProFab big bore
White Brothers cam
ported & polished head w/ +1 intake
Kibble White HD springs
38mm Keihin-choke removed
full DG RCM exhaust- want X-6
DID silent HD cam chain
K&N filter-No lid
02 Raptor-
High comp 720 kit
Web cam 461/496
K&N filter
Supertrapp exhaust
lowered 1.5"
92 250X-12:1 WIESCO .020/No-Toil filter
03 CBR954 - full 2brothers exhaust
95 Kawasaki Ninja ZX6 streetfighter
93 Honda XR80R
83 Z50R -K&N filter
98 Arctic Cat Cougar 550 liquid
86 Ski-Doo Citation
it runs good,it has a k&n air filter and a cobra exhaust.i just didnt know and was goimg to see about getting some if it didnt have it. how much of a difference would you notice if they was it there?can you tell a difference with the lid off with the k&n?thanks
Well if it runs good now, it must be jetted correctly for the mods involved. So you could leave it and not mess w/ success.....but wheres the fun in that !?
With the box lid removed w/ the K&N it would get a good amount of air, which would call for a bigger main jet for fuel. I would say it would give it a noticeable power change, most likely better throttle response.
NOTE: with the lid removed and a K&N filter, I would recommend a outer-wears prefilter, filter cover to keep debris out of your engine.
Also If you are looking for a quick, cheap, and easy power increase.... adjust the valves. Better compression gives better power.
MY TOYS
406X Honda
Powroll stroker w/ Vesrah shorty rod
ProFab big bore
White Brothers cam
ported & polished head w/ +1 intake
Kibble White HD springs
38mm Keihin-choke removed
full DG RCM exhaust- want X-6
DID silent HD cam chain
K&N filter-No lid
02 Raptor-
High comp 720 kit
Web cam 461/496
K&N filter
Supertrapp exhaust
lowered 1.5"
92 250X-12:1 WIESCO .020/No-Toil filter
03 CBR954 - full 2brothers exhaust
95 Kawasaki Ninja ZX6 streetfighter
93 Honda XR80R
83 Z50R -K&N filter
98 Arctic Cat Cougar 550 liquid
86 Ski-Doo Citation
I forgot to tell you, I have a Dynojet kit for the 300EX carburetor. BRAND SPANKIN' NEW! All the jets (8) are in the little baggies still, along with the needle, adapter, and the washers and clips needed. It also comes with the full instructions. PM me if you're interested. Thanks!
MY TOYS
406X Honda
Powroll stroker w/ Vesrah shorty rod
ProFab big bore
White Brothers cam
ported & polished head w/ +1 intake
Kibble White HD springs
38mm Keihin-choke removed
full DG RCM exhaust- want X-6
DID silent HD cam chain
K&N filter-No lid
02 Raptor-
High comp 720 kit
Web cam 461/496
K&N filter
Supertrapp exhaust
lowered 1.5"
92 250X-12:1 WIESCO .020/No-Toil filter
03 CBR954 - full 2brothers exhaust
95 Kawasaki Ninja ZX6 streetfighter
93 Honda XR80R
83 Z50R -K&N filter
98 Arctic Cat Cougar 550 liquid
86 Ski-Doo Citation