86 250r

[Prey]

have the following aftermarket itmes to part along with all the rest stock, in addition to a 265 cc cylinder and hear and another frame,

Laeger's +2 +1 A-Arms
PEP Dual Rate Front Shocks W/ Rezzies
Denton Steering Stabalizer
AC Front Bumper
Aluminum Radiator Shrouds
Armadillo Full Skid
Lone Star Swing Arm
Denton aluminum Carrier
Lone Star Adjustable Axle
Lone Star sproket hub
Lone Star Brake Stay
Lone Star Anti-Fade nut
AC Pro Pegs With Integrated Heel Gaurds
TCS Rear Shock rebuild
Galfer Brake Lines
EBC Rotors
AC Grab Bar
Full Bore Plastics
Nac's Seat Cover
VForce Delta 2 Reeds
LRD Adjustable Pipe and Silencer
K&N filter
Barnett Clutch and Basket
Carbon Fiber tank cover
Chromed Clutch Cover and Water Pump Cover
ESR 310 Engine kit (pro-x cylinder, aluminum head...etc.) (top end just re-built by kellner motorsports)
38mm Air Stryker
Roll Design anti-vibe Steering Stem
Leagers bar Clamp
Pro taper bars
RTC quick adjust clutch
RTC brake lever
Moose res cover
Raptor front master cylinder
Pro Design kill switch
Moose aluminum throttle body
2 25 fin inline coolers
ESR kickstarter
ESR brake lever
ESR mag cover
EK X-Ring Chain
Renthal/Moose Sprokets(14/41 gearing)
Jennson Racing coil
durablue anti-roll bar

make offers, bike is currently whole and running stong

[Cr85rRida]

send pics of a-arms,seat cover and full bores to cr85rrida@yahoo.com please.

[Eddiesanders250]

how much for the 310 kit and the esr kickstarter/brake pedal?

[Prey]

cr85 pics are here if thats cool, if not i can e-mail them

250R pics

[Prey]

Originally posted by Eddiesanders250
how much for the 310 kit and the esr kickstarter/brake pedal?

$600 for the top end (has the full trx7 port), bought in february of this year, used 1 bore, esr didnt chamfer the exhaust port right and went throught the 1st piston within hours. Tony Kelner correct the exhaust port and rebuilt, has about 10 hours on it since rebuild (has teflon coated piston as well) also comes with gas and race gas domes for the head

$50 for the kick start

$60 for the brake

[Cr85rRida]

Sweet those are fine. How much for the a-arms and seat cover? they come with everything to mount up right(a-arms)? And are they chrome or silver couldnt tell in the pic. thanks.

[426ex]

How much for the whole ride?

[Prey]

4200 for the bike, comes with a spare frame (no cracks or bends) and a spare 265cc cylinder and head. Also the LRD silencer is brand new (bike has not even been run since i put it on last week) and 3 additional laegers ball joints.

The only thing the bike needs as it sit are
it could use new shock bushings up front and the tranny oil plug was stripped when i bought it (i have been buying temp plugs) but if you were serious about the bike i would take it and get it tapped

[Prey]

Originally posted by Cr85rRida
Sweet those are fine. How much for the a-arms and seat cover? they come with everything to mount up right(a-arms)? And are they chrome or silver couldnt tell in the pic. thanks.

make an offer, i would like 400 for the arms, tie rods and brake lines (as i mention above, there are $100 worth of ball joints that come with them not installed yet.

as far as the seat cover, it is way too much work to seperate the seat cover from the seat for the few $$ its worth, with that said, the whole seat for 85 plus ship

[Cr85rRida]

Check your pm's.