Results 1 to 6 of 6

Thread: snorkle removal

  1. 03-20-2002, 10:19 PM #1
    liltazz
    liltazz is offline Senior Member
    Send a message via AIM to liltazz
    Join Date
    Nov 2000
    Location
    Wilkes-Barre, PA
    Posts
    247

    snorkle removal

    hey i need to know how big the hole is where the air intake tube goes into the airbox. i am at college and i cant go outside and measure it. or if anyone knows the size freeze plug needed.
    Reply With Quote Reply With Quote
  2. 03-20-2002, 10:27 PM #2
    Guest
    same diameter as a spray paint lid.... actually a little bigger but alot of people use the lid to plug the hole.
    Reply With Quote Reply With Quote
  3. 03-20-2002, 11:14 PM #3
    Deathbringer's Avatar
    Deathbringer
    Deathbringer is offline Senior Member
    Join Date
    Oct 2001
    Location
    Southern,Oregon
    Posts
    475
    If you don't want to use it as a source of air intake then cut the snorkle right after the box, there is a little lip there so it wont fall back in.. then all you need to do is tape the end on the inside and you got it...done.
    Deathbringer
    (The Corporation)



    2002 Yellow 400ex
    Armadillo Chrome Bumper
    WB E-series pipe
    WB Rev box
    Dyno Jet kit
    K&N filtering/moded airbox
    Chromed headers
    Lots of bling bling
    Reply With Quote Reply With Quote
  4. 03-21-2002, 02:56 PM #4
    R-Crazy's Avatar
    R-Crazy
    R-Crazy is offline Ride Hard or Don't Ride!
    Join Date
    Nov 2001
    Location
    Randolph, NJ
    Posts
    1,144
    why would you get rid of your snorkel?

    dave
    1986 Honda 265R, New 89 motor, ported and polished by East Coast ATV, New Stock Honda clutch/clutch basket, FMF reed cage/ spacer/ and rad valve, 38mm keihn airstriker carb, K&N w/ outerwares, FMF fatty pipe, powercore 2 and Q silencer, Laeger +2 arms, Maier plastics, BAD saddle seat cover, Works triple rate steelers w/ rezzies, MOB aluminum swingarm, Lonestar dualrow bearing carrier, Durablue +2 axle, Durablue adjustable strut, AC Bumper, AC grab bar, AC nerfs, AC chassis skid, Lonestar anti-vibe steering stem, Lonestar handlebar clamp, Renthal bars, Douglas 190's w/ holeshots, Front and rear SS brake lines, Speed easy pull clutch lever, anti-fade locknut, SS bolt kit, Rocky mountain swingarm skid, and some more little goodies!

    Football, baseball, soccer, golf, and tennis
    all take one ball
    Racing takes two!

    SN: CrasHing3283
    Reply With Quote Reply With Quote
  5. 03-21-2002, 05:17 PM #5
    Smoker's Avatar
    Smoker
    Smoker is offline I'm strong to the finish
    Join Date
    Oct 2001
    Location
    Columbus
    Posts
    714
    $10 from nacs, aluminum plug that has nacs engraved on it.
    04' 450R w/ stuff
    Reply With Quote Reply With Quote
  6. 03-22-2002, 08:53 AM #6
    ChadEXer's Avatar
    ChadEXer
    ChadEXer is offline WFO
    Join Date
    Dec 2001
    Location
    TX
    Posts
    3,385
    I had the Nacs plug on mine. I just sold it to Tlongs400 because I had an aluminum box made for mine!! The Nacs plug works good!
    Speed is 95% rider and 5% bike, better make that 5% count!

    2000 TC 505EX Complete TC Motor and everything else you can imagine and more!!
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules