parting out 440ex

[mikeboone]

Partial list of my quad--hate to see it go--money order-cashiers check-paypal accepted. There are no broken parts here--I throw out bad stuff:cool:

--------------------------------------------------------------------------------
*Stock a-arms & tierods--$115
*35 th alum 2 piece rear NEW--$35
*Main wiring harness runs front to rear of frame--$25
*Cometic gaskets-new: head, base, (2) left cover, center case gasket, starter, several rocker cap o-rings--$30
*K&N Breather filter: replaces tube from crankcase to airbox--$10
*All motor mounts with bolts/nuts--$25

__________________________________________________ __
List has been updated--items below sold to buyers**


*Spindles,rotors,calipers,front hubs,SS lines,front brake,lug nuts,steer stem,pivot bolt--$430 Aubry Nottingham

*Billet bar clamp--$15 unstopable1 {Paid-ship Tuesday}

**Rear link/stem bush--$25 Craig02 {Paid-SHIPPED}

**Clutch Perch/Lever--$10 TLongs {Paid-SHIPPED}

**16 tooth sprocket--$12 Trailburner {Paid--SHIPPED}

*Doug Rims/TT Tires--$150 TRX Mad

**High Rev CDI--$60 Prancing 400 {Paid-SHIPPED}

*Oil Tank- cable--$42 Timma ^send m/o^ -Shipped

**Airbox & manifold--$20--Jimmy Newby {Paid-SHIPPED}

**Starter/Kill Switch--$8-JHR {Paid-SHIPPED}

*Tool Box & Billet gas--$30 Xowner {Paid-Ship Tue}

*Throttle assembly--$25 (********)

*FCR 41mm carb--$325 Derrick

*Sparks X6--$350 416MX *O/H**

*Oil Cooler & key switch--$40 Niknaks

**K&N Filter--$29 E Young {Paid-SHIPPED}

*PD Billet shifter--$35 Chanman

*Battery & Box--$57--Ebay {Paid--Ship Tue}

*Renthal Bars--$52 Dr laura--

*4" swingarm--$242 911 KIDD--O/H

[Xowner]

what is a a/m clutch lever and perch is it one of them easy pull set up got pics? also how much for the motor
jpsshack@fuse.net
Thanks

[mikeboone]

sorry, aftermarket think made by sunstar? Not an easy pull--just reg. with shorty lever. I am gonna sell motor local instead of crating up.

[Xowner]

what kinda bumper u got and skids?

[Tlongs400]

NO NOT THE DRAG BIKE--WHAT ARE U DOING?????: :eek2:

[mikeboone]

No bumper-skids-nerfs-or dirt tires. This was an asphalt drag quad

[mikeboone]

TTT--:)

[sparks400ex101]

what about the front tires and rims

[mikeboone]

The fronts are Pirelli scooter tires on great looking Douglas .125 10x5 rims. $130 shipped--great for asphalt drags! or, sell the tires to a friend and keep the rims?

[Craig02]

does the shock linkage have good bearings and does it have any bolts with it?

[mikeboone]

Bearings on linkage are fine--unsure about those bolts.

[Craig02]

I pm'd you

[Bill Fuller]

PM'd you Mike.

[j37]

PMed ya.

[prancin400hp]

hey man I want that cdi rev box as soon as possible. I need it for a stage 1 hotcam

[mikeboone]

Pranicin 400hp--The high rev box is urs. I will send info via PM.

[Xowner]

take ten for the gas take secltor pm me etheir way and the tool box does it have the spark plug wrench?

Thanks

[muff]

does the pro design shifter have the little rubber thing on the end of it or is it all billet aluminum?

[416mx]

Have you still got the pipe (x6) and if you do whats your low dollar.
thanks

[mikeboone]

The shifter is billet alum complete--no rubber; made out of one piece. The X6 is still for sale--still $350

[416mx]

Can you send some pics of the pipe,
i,ve been looking for one for a while, and i,m very interested. I,m new to this message board and not sure how everything works yet . Was your drag bike always a asphault bike? Did you ever race anymotocross or cross country?
Thanks:cool:

[mikeboone]

ok, will get some pics. The quad started out as a trail bike but I changed over in 03 for aphalt only. Best of 8.14 secs at 78mph in 1/8 mile (660ft) High 13's in 1/4 mile...

[400ex_backer]

hey you read my thread is there anything you would like to trade for the billet shifter

[mikeboone]

No trades needed--thanks

[mikeboone]

Alot of stuff still for sale--most is going to Ebay tomorow what's left. The prices are well below new--some is 75% less than what you will pay at Honda dealer. :o

[Xowner]

do you have the rubber mounting hardware for the tail light?

Thanks

[mikeboone]

I dont have any parts associated with lights: clips, mounts, or any wiring. Thanks

[pnut420]

Where is the frame for this quad ;) . Im looking for a frame with title, if you have one let me know.

Thanks,
Kevin

[mikeboone]

I do still have the frame, subframe, motor, and race maier plastics. I have 20-30 ppl local that have sent messages they will buy all parts.

NC does not give titles with atv's. They only give a bill of sale with paperwork.

[mikeboone]

NIKNAKS--ur pm box is full--here is my message: Our P.O. Boxes here close at 12 noon on saturday and we have no UPS drop off anywhere around. The wiring is just the attached wiring from key switch to white clip that plugs in harness. It's about 1 ft in length--no splicing.

[NikNacs67]

I cleaned it out. Sorry about that and thanks.

[mikeboone]

TTT_Need to get all this gone. Help me out guys:cool:

[400exmanmanman]

How much for the starter?

[mikeboone]

$75 shipped for the starter. Much better deal than new through Honda.