416exmx
11-12-2003, 05:06 PM
first off here is the whole bike
ECA converted 400 frame, Houser +3 LT a-arms w/upper chrome, Houser +1 1/4 swingarm, Houser anti-vibe stem w/ Tag fatbars, Custom Axis 19" dual adjust tripple rate fronts, Custom Axis dual adjust dual rate rear, Baldwin front hubs, Baldwin carrier, Baldwin anti-fade, Baldwin throttle cover, Dominator extended axle, Durablue rear hubs, Fastline brake lines, Hinson rear brake pedal, Sprocket Specalties sprockets w/ new chain, Fullbore white plastic w/Legacy graphics & seat cover, AC pro-pegs, White bros. bumper, Douglas billet center rear beadlocks w/new Kenda Klaw MXR's, Douglas fronts w/Holeshot MX, Aftermarket pivot bolt, Full body skid plate, TC shorty exhaust system, Denton stablizer, Acerbies handguards, Aftermarket clutch/brake levers, New OEM front knuckles, ECA Oil tank, 250r radiator, 400ex airbox, Pro-design kill switch, Frame is pc'd dark purple w/chrome pc'd subframe, blue a-arms & swingarm, red stem, Motor is 01 with low hrs, Hinson basket, 10oz flywheel weight, Translucent red side cases...and more i probably am frogetting some stuff.......$7950 here is a pic.
http://www.imagestation.com/picture/sraid79/p0f6ff70acc0354d719777b1caa38b41b/fb124eb9.jpg
__________________________________________________ __
OR i will sell this stuff off it as a whole.. read here
here is what you get.
--2001 YZF426 motor, low hrs, hinson basket, 10oz flywheel weight, pc'd side covers
--FCR carb for motor
--All wiring, cables, cdi, coil and everything to make it run
--YZF headpipe with TC shorty polished silencer
--250r radiator
--Walsh-like radiator shrouds
--K&K aluminum oil tank
--Extended kickstart for 400 frame
--Frame, 400ex, that was sent to East Coast ATV, converted to accept motor and guesseted, fresh pc'd.
this is a complete set-up. all you have to do is bolt up your front-end, and rear-end, put tank, plastic, stem, and stuff like that on it. you are basicaly buying everything inside the frame including the frame.
Here is the good news. you can now own a yzf quad just like you have always wanted to. buy all this and sell all your stuff you dont need...example- your frame, motor, exhaust and everything else. for what i would probably take for all this is probably close to what you could get out of all your stuff. then you have almost the same in your quad as you did although now you have the all mighty YZF426 motor..............$3200 for all that.
dont ask for other parts for that is all that is going for now.
my e-mail is farmbig_01@otbnet.com here is a pic
http://www.imagestation.com/picture/sraid74/p209f54bbbc0462baffaa954182c8978f/fb627f30.jpghttp://www.imagestation.com/picture/sraid79/p0f6ff70acc0354d719777b1caa38b41b/fb124eb9.jpg.thumb.jpg
ECA converted 400 frame, Houser +3 LT a-arms w/upper chrome, Houser +1 1/4 swingarm, Houser anti-vibe stem w/ Tag fatbars, Custom Axis 19" dual adjust tripple rate fronts, Custom Axis dual adjust dual rate rear, Baldwin front hubs, Baldwin carrier, Baldwin anti-fade, Baldwin throttle cover, Dominator extended axle, Durablue rear hubs, Fastline brake lines, Hinson rear brake pedal, Sprocket Specalties sprockets w/ new chain, Fullbore white plastic w/Legacy graphics & seat cover, AC pro-pegs, White bros. bumper, Douglas billet center rear beadlocks w/new Kenda Klaw MXR's, Douglas fronts w/Holeshot MX, Aftermarket pivot bolt, Full body skid plate, TC shorty exhaust system, Denton stablizer, Acerbies handguards, Aftermarket clutch/brake levers, New OEM front knuckles, ECA Oil tank, 250r radiator, 400ex airbox, Pro-design kill switch, Frame is pc'd dark purple w/chrome pc'd subframe, blue a-arms & swingarm, red stem, Motor is 01 with low hrs, Hinson basket, 10oz flywheel weight, Translucent red side cases...and more i probably am frogetting some stuff.......$7950 here is a pic.
http://www.imagestation.com/picture/sraid79/p0f6ff70acc0354d719777b1caa38b41b/fb124eb9.jpg
__________________________________________________ __
OR i will sell this stuff off it as a whole.. read here
here is what you get.
--2001 YZF426 motor, low hrs, hinson basket, 10oz flywheel weight, pc'd side covers
--FCR carb for motor
--All wiring, cables, cdi, coil and everything to make it run
--YZF headpipe with TC shorty polished silencer
--250r radiator
--Walsh-like radiator shrouds
--K&K aluminum oil tank
--Extended kickstart for 400 frame
--Frame, 400ex, that was sent to East Coast ATV, converted to accept motor and guesseted, fresh pc'd.
this is a complete set-up. all you have to do is bolt up your front-end, and rear-end, put tank, plastic, stem, and stuff like that on it. you are basicaly buying everything inside the frame including the frame.
Here is the good news. you can now own a yzf quad just like you have always wanted to. buy all this and sell all your stuff you dont need...example- your frame, motor, exhaust and everything else. for what i would probably take for all this is probably close to what you could get out of all your stuff. then you have almost the same in your quad as you did although now you have the all mighty YZF426 motor..............$3200 for all that.
dont ask for other parts for that is all that is going for now.
my e-mail is farmbig_01@otbnet.com here is a pic
http://www.imagestation.com/picture/sraid74/p209f54bbbc0462baffaa954182c8978f/fb627f30.jpghttp://www.imagestation.com/picture/sraid79/p0f6ff70acc0354d719777b1caa38b41b/fb124eb9.jpg.thumb.jpg