PRP products question

[400MXer]

Does anyone know if there stuff is good. I don't know anyone around here that runs their stuff. About how much do their frames cost. Are they no-link? Do they make one for a CRF motor.
Who carries PRP products.
Do any of your have their address and phone number?

[K_Fulk]

I have a prp seatlatch:rolleyes: . Exodous racing sells there frames here is there website I'm sure they could answer your questions they have had some of there frames go through there. http://www.exoduscycles.com

[Ben Bettis]

PRP's number is ***-***-****. They may not answer but if you leave a message, Dave will get right back to you. They build excellent frames and other chassis components. I have ridden one of thier no-ling long travel chasis for 2 years on the GNC circuit and haven't had one problem with it. They make CR linkage bikes too. Also billet front hubs,steering stems,subframes, bearing carriers, a-arms and swingarms and are cheaper than most other companies.

[rydes400ex]

I have been running a prp long travel front end all year. There pretty nice and are built heavy duty

[400MXer]

Ben, could you PM me their number. also, do you have any pics of the bike, frame.......and i would like to see pics of their long travel a arms.

also, do you have a rough estimate on price of frame & sub, and swingarm?

[beyer05]

JH racing sells their stuff.

[hondamxer161]

they do make a crf frame. it runs crf linkage as well. their stuff looks awesome. i got a friend with one going together right now!

mike

[400MXer]

could you get some pics of your friends bike?

[4wheelboy]

rule # 5

:rolleyes:

[400MXer]

I think that is pretty off when it comes to rule #5. i can't find PRP's number or address and ben gave it to me but you deleted it! I thought this was an informational forum?

[Dave400ex]

I would also like to see some pictures. Never really heard of or seen this stuff. I agree, Rule #5 does not really effect this one because he is asking for the info, nobody is straight up advertising for PRP.

[jlr70]

Just email Bettis - I am sure he will get you the number again!

[hondamxer161]

no pictures of the PRP. it will be shown for builder of the year...

mike

[racerx573]

I have a PRP CR500 link swingarm, and it's pretty sweet, just like a Laeger. I ran it all season, and no problems. It came w/ the front chain slider too. E-mail Sean Berkey, he has a PRP R, it's pretty nice. sdberkey@aol.com he answered all my PRP questions.

[pnut420]

Wow, I thought he was just kidding about ther rule #5. So we can give out websites but not phone numbers? :confused:

[JH Racing16]

I rode Leager before I got my PRP and I beleive the PRP handles alot better than the Laeger. I have sold quiet a few frames in the last 2 years and everyone has been very happy with them Yes the CRF uses CRF linkage. I switched to the CRF right before high point and I am a very happy with it.

[400MXer]

Did you use their front end too? how does that compare. And could you PM me a price on the chassis?

[JH Racing16]

I use their A-arms swingarm, front hubs,anti-fade lock nut, bearing carrier, and steering stem. It does not push as bad as the leager does.

[forum]

theres fine line when it comes to rules like that.I persoanly dont see a problem with it. but. Don't question the moderators. just have him PM you.

[KandK952]

I run a PRP CRF450R and it works great. The only thing I do not have of his is a front end... I already had a long travel front end but I hear his work really well and turn on a dime. His setup in the rear with the CRF linkage works awesome.

ive talked to dave porter a few times he seems like a good guy,id buy from him, a couple of my freinds have his stuff and like it

[400MXer]

does anyone have any pics of his stuff....i'm really curious to see his LT front end!