300ex

[cheesy350]

i want to get new handle bars for my 2003 300ex but i dont no where to put the the ignition holder...leave some suggestions













2003 300ex-stock for right now

[300exOH]

You can bore a hole on the right side of the ring that goes around the fuel tank.

[Chanman420q]

u can either drill a hole in the plastic, get rid of the ignition or i think u can get a 250x ignition holder at a honda dealer....


aw puchie kid made a thread:rolleyes:

[stonerider250x]

the 250x ignition is in the same place as it is on the 300ex and when i baught new handle bars i had to take my ignition off cause i didnt want to drilla hole in my plastic

[ZSK]

I cut the "flaps" off of the sides and just kept the middle (mine's on the left, best pic I got)it's tight but I can still get the key in and out even with a crossbar

http://www.imagestation.com/picture/sraid71/p22f91d49c335bff678bfe984bf5b67ea/fb86eb00.jpg

[bigfoot300ex]

i zip-tied mine to the front brake rezi

[250x#93]

Originally posted by cleanshave300ex
I cut the "flaps" off of the sides and just kept the middle (mine's on the left, best pic I got)it's tight but I can still get the key in and out even with a crossbar

http://www.imagestation.com/picture/sraid71/p22f91d49c335bff678bfe984bf5b67ea/fb86eb00.jpg

Damn thats a good idea:devil:

[Diedrich]

yeah i drilled a hole in the side of my plastic..i mean if u dont like it u can buy a new plastic piece for like $5. but i think it looks trick

[atvman6988]

my reverse has been removed so i drilled out the reverse light in the head light plastic houseing it looks all right and is very practical (no reaching under frame ect) and it looks somewhat stock

[bayou boy]

when I changed the bars on mine I made a bracket out of aluminum. it bolts to the headlight assembly where the phillips head srews are just inside where the bolt holes are in the headlight plastic for the handle bar bolts. the switch fits neatly between the bars and the headlight and it kind of fills that hole between them. It is strong and ez to make and it looks good as well..

[atv223]

Tom Miller Motorsports makes a billet Al bar clamp that the swith fits into. It works and looks great!!

[quad_racer_19]

just look a bit fown in the forums there is a thing called 300ex key relocate that i had posted check it out...lots of pics

[sportraxrider10]

i made a bracket out of aluminum, it looks like this
http://www.imagestation.com/picture/sraid75/pa16c02b463b149eac0e63f67f441bde5/fb51ebd2.jpg
http://www.imagestation.com/picture/sraid75/pe70ed1a2c9b436d190dbb3edd6db9a9f/fb51ec83.jpg
http://www.imagestation.com/picture/sraid75/p1bc7025c7e27ac80624d3326726ea8b2/fb51ebd6.jpg

:macho

[quad_racer_19]

hey honda300ex06

on your handlebar brackets did you have to stick any washers underneath your key mounting plate because i see there is a grove on my bracket

[Diedrich]

hey man that brackets looks good

[sportraxrider10]

Originally posted by quad_racer_19
hey honda300ex06

on your handlebar brackets did you have to stick any washers underneath your key mounting plate because i see there is a grove on my bracket


i'm not exactually sure what your talking about, could you explain what you mean more about the brackets?

[Out_Sider]

i just zip tied mine to the bottom of my handle bars-inbetween the clamps- works great-doesnt look trick or nothing, but it gets tha job done :macho