Will a quad fit in the back of a ford ranger?

[exrider4life]

I'm gettin a 4x4 ford ranger soon, and i'm curious to see if a quad will fit int he bed ok. i think it would fit but i'm not sure. I'm pretty sure i'd have to put the tailgate down atlest. well, thanks, STEVE

[Stevie-D]

ive seen an EX in the back of a Colt before:eek2: , so ya, it will fit:D

[Honda4trax250x]

what kind of quad it depends:rolleyes: either way tho i think a quad should fit

[CHAUNCY]

If this guy could do this........I'm sure you can make it fit;)

fits no problem


my freind carrier his r in the back of his and i put my 400 in ares tail gate up

[Chino]

my 400 fits fine in the back of my toyata with tailgate up but i got a big enclosed trailer on order and wont' have to worry bout that no more :macho

[kxrider]

step side it wont fit, regular it will

[Giz400ex]

I know a Honda Rancher does but I'm sure on how much wider the quad you have versus the rancher is??? You better take a look and take measurements first if you plan on hauling the quad. My quad barely fits in the back of my Ram!!:eek2:

[KrazyKid300ex]

well what the bed is about as a big as a s-10 right? my 300 squeezes between the wheel wells. when my dad had a polaris 300 explorer it fit too but he drove over one wheel well to get it in. The grizzly fits too now so i think you'll be fine. The step side Rangers do not have the wheel wells but a regular bed does.

[blondie69]

Originally posted by CHAUNCY
If this guy could do this........I'm sure you can make it fit;)

LMFAO!!

well......theres only 1 way to see if it will fit.....put the tail gate down, lay some boards down n make a ramp and haul @ss up the ramp....

[FourFiftyFour]

My friend has a 2002 Banshee and he dented up the fender wells BAD on his ranger (brand new ranger), and he did the classic, break the back windshield routine. But the Banshee... you have to SQUEEZE it through with the fender wells dented......... its a tough fit............ I'd advise to get a trailer

[Bill Fuller]

I owned a '99 Ford Ranger step side and a 400ex,the 400 will fit in the back of the bed providing you have the strength to litterally pick it up over the wheel wells even after they were dented all to he11.That Ranger was a piece of crap,couldn't pull a stick out of the mud(v-6).I took alot of grief from my so called friends about that truck and I did measure the bed I thought it was the perfect fit,turns out theres a lip around the tailgate I forgot to consider.:mad:

[FoxRacing400EX]

i got a 98 ranger with stepsides and i can get a 300 in real easy, but when it come to the 400 it's a lot more trouble. it's pretty much a two person job, one needs to help keep the front lined up so it dosen't bind on t he wheel wells, and the need to pick up the whole rear of the quad to lift the tires higher than the bed and set it in... I thought about trying to make something that would sit in the bed to make it eaiser to load but have lagged a lot on that project. it just sucks that those two pieces that stick out are just that half inch too far to slip the quad in...:mad: . if you have a standard bed you shouldn't have any problems though.

[Juggalo]

my friend put his 400ex in the back of his ranger all the time.

[dj416]

i had a step side ranger and with alittle help from a friend it would fit with the tail gat up, u just pretty much have to pick it up and over the tailgate opening

[skemp]

I have a '92 which is a regular bed, and I just use an aluminum ramp, drive it in, stick the ramp under it, and flip the tailgate up. Fits with plenty of room.

[bigbadbrad]

with my 300ex i would have to lift the front over the wheel wells in my brothers ranger. i have offset rimms though. my dads trx300 4x4 just squeezed right in between the whell wells aand dented ona a little but we just popped it back out

[balla250ex]

My 250ex fits in the back of my dads s-10 short cab ;)

[JustRace]

it was a PIA getting my EX in the back of my s-10. Had to go over the wheel wells and one time i slipped on the throttle popped a wheely and slammed into the front of the box breaking the welds on the box and denting the back of my cab. lol Oh well. lol :confused2

[CHAUNCY]

Originally posted by JustRace
it was a PIA getting my EX in the back of my s-10. Had to go over the wheel wells and one time i slipped on the throttle popped a wheely and slammed into the front of the box breaking the welds on the box and denting the back of my cab. lol Oh well. lol :confused2

LOL
I would hate to have that happen to me:(

[250x#93]

MY X fits in the back of my pa's nissan pickup:)