jhtrx250r
10-28-2013, 09:15 PM
set of freshly rebuilt works performance tripple rate remote rezie shocks
valved and sprung for a 170-205 lb rider +2 a arms dunes and XC, should work for stock a arms rider weight 205-235 these also fit 400ex
New seal kit new bladders, new oil 250psi dry nitrogen $400
boyesen rad valve 02A with brand new reeds (reeds alone where $80) $115
Kehin PWK 38mm air striker carburetor, pre jetted from sudco for trx250r with 310cc motor $190
Lonestar twin row bearing carrier $100
Durablue twin row carrier $75
Paul turner (I was told) ported 88 cylinder 67.5mm fresh bore with new piston done by superior sleeve decked .040 $300
(With power head below $400)
Paul turner Power Head (cool head) with brand new 22cc dome and used 18cc dome $145
Stock 86 jug clean up ported cylinder cut for o rings (uses pro designs) with nice low hour piston and head run time was sox. 20 hrs $275
Freshly built 1988 bottom end Flawless cases (cases bored and machined to fit up to a 350ss cylinder) gears are perfect all bearings seals and gaskets where replaced, new hot rods CK109 long rod crank shaft, New Moose heavy duty bilit clutch basket, new bolts fresh creamic coat paint assembled read for a top end
$1400
RPM adjustible timing advance $40
Teather kill used a few times nice like new $25
2 full un cut main wire harness $65 each
Used oe CDI boxes $40 each
New 400ex CDI box was told it fits 250r? $80
V force cage w/used reeds $70
Nice 87 front caliper pair (no pads) $75
All above parts are in top knotch condition, I will up load pictures when I can get some, so hit refresh if you dont see them in the add or email me your email or phone # I can send pics
ricks stator 100w stator $70
New K&N air filter $45
Used once K&N filter $40
Offers are OK , if I font like it ill say no.
Tons of new chassis bolts , and used frame rubbers
All parts in great like new shape email me with questions or for better pics of an individual item?
Thanks james , email at jhtrx250r@yahoo.com
valved and sprung for a 170-205 lb rider +2 a arms dunes and XC, should work for stock a arms rider weight 205-235 these also fit 400ex
New seal kit new bladders, new oil 250psi dry nitrogen $400
boyesen rad valve 02A with brand new reeds (reeds alone where $80) $115
Kehin PWK 38mm air striker carburetor, pre jetted from sudco for trx250r with 310cc motor $190
Lonestar twin row bearing carrier $100
Durablue twin row carrier $75
Paul turner (I was told) ported 88 cylinder 67.5mm fresh bore with new piston done by superior sleeve decked .040 $300
(With power head below $400)
Paul turner Power Head (cool head) with brand new 22cc dome and used 18cc dome $145
Stock 86 jug clean up ported cylinder cut for o rings (uses pro designs) with nice low hour piston and head run time was sox. 20 hrs $275
Freshly built 1988 bottom end Flawless cases (cases bored and machined to fit up to a 350ss cylinder) gears are perfect all bearings seals and gaskets where replaced, new hot rods CK109 long rod crank shaft, New Moose heavy duty bilit clutch basket, new bolts fresh creamic coat paint assembled read for a top end
$1400
RPM adjustible timing advance $40
Teather kill used a few times nice like new $25
2 full un cut main wire harness $65 each
Used oe CDI boxes $40 each
New 400ex CDI box was told it fits 250r? $80
V force cage w/used reeds $70
Nice 87 front caliper pair (no pads) $75
All above parts are in top knotch condition, I will up load pictures when I can get some, so hit refresh if you dont see them in the add or email me your email or phone # I can send pics
ricks stator 100w stator $70
New K&N air filter $45
Used once K&N filter $40
Offers are OK , if I font like it ill say no.
Tons of new chassis bolts , and used frame rubbers
All parts in great like new shape email me with questions or for better pics of an individual item?
Thanks james , email at jhtrx250r@yahoo.com