sammy5x
12-20-2012, 10:22 AM
2004/5 were the best years for the TRX450R:
2nd owner -- I worked at the dealership at that time, sold it to the original owner and did all the maintenance to it. It sat in storage from spring 2006 thru spring 2010.
UNDER 12 HOURS ON MACHINE AND UNDER 4 HOURS ON PISTON & CAM SINCE THE FULL OVERHAUL/BUILD
NEW POWDER-COAT ON ALL PAINTED SURFACES
NEW CADMIUM PLATING ON ALL NUTS/BOLTS AND BRACKETS
LEUMAS ENTERPRISES:
FULL FRAME GUSSET KIT
LOWERED CRO-MOLY SUBFRAME WITH ADJUSTABLE REAR MOUNTS
SKID PLATES & CHAIN GUILD
FOOT-PEGS/FOOT-PEG BRACKETS/SHIFTER
MACHINED REAR BRAKE PEDAL FOR SEALED CARTRIDGE BEARINGS
HEAVY DUTY SHOCK BOLTS/SPROCKET BOLTS
MOOSE RACING:
SEAT COVER
FRONT BUMPER
FUEL SCREW
CLUTCH PERCH/LEVER
BRAKE ROTORS
HANDLEBARS
PARKING BRAKE PLATE
STAINLESS STEEL RE-USABLE OIL FILTER
PROTAPER PILLOW TOP GRIPS
ELKA FACTORY STAGE 5 LONG TRAVEL SHOCKS FRONT & REAR WITH PRO-DUAL LINKAGE
JD PERFORMANCE +3" MAX GROUND CLEARANCE LONG TRAVEL A-ARMS WITH SEALED NEEDLE BEARINGS
LAEGER +1" CHROME STEERING STEM
CUSTOM HANDLEBAR CLAMPS
STREAM LINE 11-WAY ADJUSTABLE STEERING DAMPER
STREAMLINE FRONT BRAKE LINES
RPM REAR AXLE/TAPERED BEARING CARRIER/BRAKE HUB
PRO ARMOR NERF BARS AND HEEL GUARDS
MOTO-WORKS SEAT FOAM WITH CUSTOM SUPPORT HUMP
G4 GRAPHICS
HMF BIG CORE FULL EXHAUST WITH CARBON FIBER SILENCER
HOT CAM STAGE 2
CYLINDER WORKS BIG BORE KIT WITH CUSTOM CP 13.5:1 PISTON
HOT RODS STROKER CRANK (BALANCED)
*** TOTAL 500cc
FULL SERDI-CUT VALVE JOB BY HMP
SUNSTAR SPROCKETS
DID ATV X-RING CHAIN
MAXXIS RAZR MX TIRES FRONT & REAR
DWT WHEELS
UNIFILTER AIR FILTER
NEW OEM CRF450 DIRTBIKE MODS:
RUBBER HANDLE BAR MOUNTS
CDI IGNITION BOX
WIRE HARNESS WITH PRO-DESIGN TETHER SWITCH
CUSTOM MACHINED BRACKET TO USE THE STATOR AND FLY-WHEEL IN ATV MOTOR
HOT START CABLE
THROTTLE POSITION SENSOR
42mm FCR CARB WITH:
TOKYO MODS THROTTLE SPRING
BOYESEN QUICK START 3 PUMP COVER
ZIP-TY FUEL BOWL SCREW COVER WITH MAGNETIC BASE
STAILESS STEEL ALLEN HARDWARE
NEW OEM PARTS:
CRANK BEARINGS
COUNTERSHAFT BEARINGS
COUNTER BALANCER BEARINGS
ALL SEALS/O-RINGS/GASKETS IN ENTIRE MOTOR
CAM CHAIN
FULL CLUTCH KIT -- FIBERS/METALS/SPRINGS
TRANSMISSION
2010 RADIATOR
2010 GAS TANK WITH COVER/PET-COCK/FUEL LINE
2010 FRONT & REAR FENDERS/BRACKETS/RUBBER MOUNTS
2010 AIRBOX AND INTAKE BOOT
2010 SWING-ARM
2010 HEAD COVER BOLTS
FRONT & REAR BRAKE PADS
WATER PUMP MECHANICAL SEAL/SHAFT
SPARK PLUG
UPPER & LOWER STEERING BEARINGS
KICK STARTER
FRONT WHEEL BEARINGS
VALVES/VALVE SEALS/VALVE SPRINGS
CLUTCH AND THROTTLE CABLES
INTAKE MANIFOLD AND CLAMPS
RUBBER EXHAUST MOUNTS
I built this just as an MX practice machine and play bike as I race XC ATV races and spend all my time in the woods. I am switching to all Yamaha YFZ450X/R FI machines for 2013+. $7500.00 or will only trade for a 2009+ SUPER CLEAN, LOW HOUR YFZR or X alum frame/FI or a 700 Grizzly with power steering. No other trades will be considered. I spared no expence and spent 2 years building this $22k + value machine and do not need to sell, but would like to match up my XC ATV with the same for MX. Located in Foxboro, MA. I will be attending the AMA awards banquet in OH in January as well. 781-801-3293
2nd owner -- I worked at the dealership at that time, sold it to the original owner and did all the maintenance to it. It sat in storage from spring 2006 thru spring 2010.
UNDER 12 HOURS ON MACHINE AND UNDER 4 HOURS ON PISTON & CAM SINCE THE FULL OVERHAUL/BUILD
NEW POWDER-COAT ON ALL PAINTED SURFACES
NEW CADMIUM PLATING ON ALL NUTS/BOLTS AND BRACKETS
LEUMAS ENTERPRISES:
FULL FRAME GUSSET KIT
LOWERED CRO-MOLY SUBFRAME WITH ADJUSTABLE REAR MOUNTS
SKID PLATES & CHAIN GUILD
FOOT-PEGS/FOOT-PEG BRACKETS/SHIFTER
MACHINED REAR BRAKE PEDAL FOR SEALED CARTRIDGE BEARINGS
HEAVY DUTY SHOCK BOLTS/SPROCKET BOLTS
MOOSE RACING:
SEAT COVER
FRONT BUMPER
FUEL SCREW
CLUTCH PERCH/LEVER
BRAKE ROTORS
HANDLEBARS
PARKING BRAKE PLATE
STAINLESS STEEL RE-USABLE OIL FILTER
PROTAPER PILLOW TOP GRIPS
ELKA FACTORY STAGE 5 LONG TRAVEL SHOCKS FRONT & REAR WITH PRO-DUAL LINKAGE
JD PERFORMANCE +3" MAX GROUND CLEARANCE LONG TRAVEL A-ARMS WITH SEALED NEEDLE BEARINGS
LAEGER +1" CHROME STEERING STEM
CUSTOM HANDLEBAR CLAMPS
STREAM LINE 11-WAY ADJUSTABLE STEERING DAMPER
STREAMLINE FRONT BRAKE LINES
RPM REAR AXLE/TAPERED BEARING CARRIER/BRAKE HUB
PRO ARMOR NERF BARS AND HEEL GUARDS
MOTO-WORKS SEAT FOAM WITH CUSTOM SUPPORT HUMP
G4 GRAPHICS
HMF BIG CORE FULL EXHAUST WITH CARBON FIBER SILENCER
HOT CAM STAGE 2
CYLINDER WORKS BIG BORE KIT WITH CUSTOM CP 13.5:1 PISTON
HOT RODS STROKER CRANK (BALANCED)
*** TOTAL 500cc
FULL SERDI-CUT VALVE JOB BY HMP
SUNSTAR SPROCKETS
DID ATV X-RING CHAIN
MAXXIS RAZR MX TIRES FRONT & REAR
DWT WHEELS
UNIFILTER AIR FILTER
NEW OEM CRF450 DIRTBIKE MODS:
RUBBER HANDLE BAR MOUNTS
CDI IGNITION BOX
WIRE HARNESS WITH PRO-DESIGN TETHER SWITCH
CUSTOM MACHINED BRACKET TO USE THE STATOR AND FLY-WHEEL IN ATV MOTOR
HOT START CABLE
THROTTLE POSITION SENSOR
42mm FCR CARB WITH:
TOKYO MODS THROTTLE SPRING
BOYESEN QUICK START 3 PUMP COVER
ZIP-TY FUEL BOWL SCREW COVER WITH MAGNETIC BASE
STAILESS STEEL ALLEN HARDWARE
NEW OEM PARTS:
CRANK BEARINGS
COUNTERSHAFT BEARINGS
COUNTER BALANCER BEARINGS
ALL SEALS/O-RINGS/GASKETS IN ENTIRE MOTOR
CAM CHAIN
FULL CLUTCH KIT -- FIBERS/METALS/SPRINGS
TRANSMISSION
2010 RADIATOR
2010 GAS TANK WITH COVER/PET-COCK/FUEL LINE
2010 FRONT & REAR FENDERS/BRACKETS/RUBBER MOUNTS
2010 AIRBOX AND INTAKE BOOT
2010 SWING-ARM
2010 HEAD COVER BOLTS
FRONT & REAR BRAKE PADS
WATER PUMP MECHANICAL SEAL/SHAFT
SPARK PLUG
UPPER & LOWER STEERING BEARINGS
KICK STARTER
FRONT WHEEL BEARINGS
VALVES/VALVE SEALS/VALVE SPRINGS
CLUTCH AND THROTTLE CABLES
INTAKE MANIFOLD AND CLAMPS
RUBBER EXHAUST MOUNTS
I built this just as an MX practice machine and play bike as I race XC ATV races and spend all my time in the woods. I am switching to all Yamaha YFZ450X/R FI machines for 2013+. $7500.00 or will only trade for a 2009+ SUPER CLEAN, LOW HOUR YFZR or X alum frame/FI or a 700 Grizzly with power steering. No other trades will be considered. I spared no expence and spent 2 years building this $22k + value machine and do not need to sell, but would like to match up my XC ATV with the same for MX. Located in Foxboro, MA. I will be attending the AMA awards banquet in OH in January as well. 781-801-3293