My office center piece [Archive]

UglyMotha™

03-12-2003, 10:32 AM

anyone ever build there quad in their office at work

mine so far now i just got to figure out how i will get it out when i'm done:huh

Glow Plug

03-12-2003, 10:38 AM

awsome what do you do where you work?

UglyMotha™

03-12-2003, 11:12 AM

i'm a design engineer here www.lpstechnology.com

UglyMotha™

03-13-2003, 08:27 AM

i need a cam really bad it's the only thing holding me up:(

tants

03-13-2003, 10:34 AM

are you the boss?

exriderdude

03-13-2003, 10:55 AM

just flip it up on its side and take it out the door... we had to do that to mine one time:o

UglyMotha™

03-13-2003, 11:02 AM

it would be nice to be the boss but i'm not:(

getting it out the door will be cake since they are double wide it's the flight of stairs i'm worried about:eek:

Glow Plug

03-13-2003, 11:30 AM

ride down it down the stairs lol

Quadfather

03-13-2003, 11:36 AM

What kind of cam are you going with?

UglyMotha™

03-13-2003, 11:40 AM

was goin to go with the stage II but it's been over a month and i still don't have it and don't know when i'll get it:(

Sparks425Ex

03-13-2003, 01:21 PM

Start her up inside and ride that bad mutha down and out side...

lil400exman

03-13-2003, 02:09 PM

nice lookin quad for a ugly mother.................:blah seriously looks nice man.........:)

UglyMotha™

03-13-2003, 02:15 PM

thanks

Rip_Tear

03-13-2003, 06:07 PM

Looking real good! I wouldnt suggest putting the A-arms or axle on it... :D Unless your going to jump it out your window... :p

Glow Plug

03-13-2003, 06:19 PM

rip-tear has a good ponit why don't you do everything besides putingthe axle and a-arms on and then go out side and bolt up you a-arms and axle on and wheel it into the truck :)

Team Outlaw #34

03-13-2003, 06:33 PM

well how big is your window? i'm sure jon could fix you up a ramp and you could jump it out the window....unless of course it is more that a story high then you might have a problem....:eek2:

Silverfox@C&DRacing

03-13-2003, 06:35 PM

Your bike is looking good. Keep up the good work.. :D
must be nice to work on it at work.. :p

UglyMotha™

03-14-2003, 07:42 AM

for anyone who ever wanted to know how to powder coat or chrome plate you a-arms there you have it plus it will only cost you 40 bucks if you know how to weld

UglyMotha™

03-14-2003, 07:44 AM

even got some new perty boots and a grease zerk now it's the same tierod end still i just swapped out the innerd's with some better stuff and welded the cap back on

Chanman420q

03-14-2003, 07:46 AM

how did u get it up there? lol

UglyMotha™

03-14-2003, 07:51 AM

Originally posted by Chanman420q
how did u get it up there? lol

in the office, i just started assembling in there piece by peice as i got them done and whala, quads are alot smaller when there in a bunch of pieces:p

Chanman420q

03-14-2003, 07:55 AM

get a fork lift and push it on the forks out the window, then just lower it down :p

UglyMotha™

03-14-2003, 07:57 AM

Originally posted by Chanman420q
get a fork lift and push it on the forks out the window, then just lower it down :p

seriously to tell you the truth, that's what me and my buddy were planning on doin seems like the best idea at the moment

Chanman420q

03-14-2003, 07:58 AM

Originally posted by UglyMotha
seriously to tell you the truth, that's what me and my buddy were planning on doin seems like the best idea at the moment

safest too

@Bad465EX

03-14-2003, 03:23 PM

I wish I had it in my office