drtrider145
08-28-2012, 01:34 PM
Here is something for starters, please don't lowball me , but I will consider offers. all items are plus shipping , These are photos of the bike at the silver state 300 race with 10 miles on it, it lost the oil seal at race mile 40 so it has a total of less than 50 miles on everything that is listed as new or freshly rebuilt, everything else is used More detailed photos to come
>
> Polaris parts list
> New red single bead lock rims, one pair, 10 inch 6+1 offset rims only no tires $300 less than 50 miles
(4) rear Polaris outlaw IRS bolt pattern douglas yellow lable wheels $100 a pair rims only tires will be removed
> Radiator $50 8 out of 10
> Radiator with fan $75 like new with coolant bottle
> PWR oversized Radiator with mounted dual fans $150 and Rath radiator shrouds and coolant bottle
Complete hydraulic clutch system $150 freshly rebuilt less than 50 miles including slave cylinder
> Extended plus 1 steering stem with rock riser and new bearings and idler stem $150 this is a stock Stem that was custom built adding 2 inches
Stock stem with double steering arms $100
> Stock rear a arms great shape including upper arm $150
I also have(2) rev boxes ,one stock $50 and one modified by polaris for John Shafe which has 1K Rpm higher rev limit
shoot offers > Plastic all race cut $200 ,including one extra white side panel red white and black tank cover
> Bumper ,$50
Full CT racing Pipe and header $250
Nerf bars with IMS Pro pegs and NEW tuff nets $175
Full Belly skid plate $75
RPM Aft Skid plate $50
Stock fuel tank with petcock $50
Stock headlights $50 for the pair
> Rear grab bar$50
> Stock sway bar $50
Front master cylinder $50 50 miles on rebuild
> Fuj custom rear sway bar $100 50 miles on it
> Fuj center link $40 50 miles on it
> Bob oil cooler kit with PWR oil cooler and stainless steel braided lines with quick connect bypass $175 50 miles on it
> Stock rear shocks $ 100 for the pair
> Stock front a arms with tie rods $200 and spindles $150 with out spindles
> New in the box EBC clutch rebuild kit including springs $130
> Stock axles $60 no CV's or boots for the pair
Stock Rear a Arms $100 for the pair
> Custom no fail seat brace $20 keeps the front of the seat from caving in on top of the carb and intake
> black seat in great shape $100
Black Seat with good pan but ripped cover $60
Red seat cracked pan small rip incover $40
> 42 mm FCR carb bored by racers edge in Tucson $300 including twist throttle 50 miles on it
> Pulser coil $30
> Custom intake and air box with 3 huge new K&N air filters $100 KMS Dyno showed 5hp gain with just this
Stock Undamaged Camshaft $50
> Elka stage 4 freshly rebuilt long travel front shocks $800 with shock covers 2 shocks
> Rear stage 4 freshly rebuilt long travel shocks $600 2 shocks shock covers
> Custom extended plus 2 long travel rear A arms less than 50 miles on them $400 including rear extended axles and CV's and boots Built by max Hernandez a pro desert racer out of Phoenix
> Custom long travel power coated gray front plus 2 a arms built by FST fabrication out of Phoenix $500 including spindles and brake calipers and extended brake lines
> Or the entire long travel front and back set up for $1800 including extended ss brake lines, shocks
> Rear hubs carriers with new fag bearings $ 50 each
> Rear center hub with welded sprocket lol $175 this has the grease zero mod already done and upgraded main bearings and includes the brake rotor
> Front Honda bolt pattern LSR hubs with tapered bearings $200 including rotors
Rear brake master cylinder $50 complete rear brake pedal to caliper $100
Front Brake master cylinder $50
> Electrical harness including switch $100 each (2) of these
Starter $50
Freshly rebuilt crank after melt down by crank works, Falicon rod and welded pin and AC bearing mod $400 like new ZERO hours
Blown motor $200 AC bearing Mod done to the cases Includes cylinder, clutch , transmission internals ect.. , NO crank, cylinder head or starter motor
Head has been Ported, polished, +1 valves and Bench flowed by racers edge in Tucson Az that cost us $900 alone it is damaged and Will require rebuild $100 Update on motor, crank is Rebuit Hot rod balanced and welded rebuilt with Honda Ball bearings, does not need cases to go with asking $400 zero hours on it ,, the motor cases and head is in worse shape than I was orginally informed of , so with that I've add new photos and taking offers on the motor parts, the camshaft is usable as is cltuch and transmission are in good shape
All motor work can be Confirmed by Kelly at KMS performance 2823 N 36th Ave # 110 Phoenix, AZ 85009
(602) 442-4340 http://www.kmsperformance.com/
>
You may contact me anytime , e mail or by phone . text is best
Joe At 602-435-2230
>
>
> Polaris parts list
> New red single bead lock rims, one pair, 10 inch 6+1 offset rims only no tires $300 less than 50 miles
(4) rear Polaris outlaw IRS bolt pattern douglas yellow lable wheels $100 a pair rims only tires will be removed
> Radiator $50 8 out of 10
> Radiator with fan $75 like new with coolant bottle
> PWR oversized Radiator with mounted dual fans $150 and Rath radiator shrouds and coolant bottle
Complete hydraulic clutch system $150 freshly rebuilt less than 50 miles including slave cylinder
> Extended plus 1 steering stem with rock riser and new bearings and idler stem $150 this is a stock Stem that was custom built adding 2 inches
Stock stem with double steering arms $100
> Stock rear a arms great shape including upper arm $150
I also have(2) rev boxes ,one stock $50 and one modified by polaris for John Shafe which has 1K Rpm higher rev limit
shoot offers > Plastic all race cut $200 ,including one extra white side panel red white and black tank cover
> Bumper ,$50
Full CT racing Pipe and header $250
Nerf bars with IMS Pro pegs and NEW tuff nets $175
Full Belly skid plate $75
RPM Aft Skid plate $50
Stock fuel tank with petcock $50
Stock headlights $50 for the pair
> Rear grab bar$50
> Stock sway bar $50
Front master cylinder $50 50 miles on rebuild
> Fuj custom rear sway bar $100 50 miles on it
> Fuj center link $40 50 miles on it
> Bob oil cooler kit with PWR oil cooler and stainless steel braided lines with quick connect bypass $175 50 miles on it
> Stock rear shocks $ 100 for the pair
> Stock front a arms with tie rods $200 and spindles $150 with out spindles
> New in the box EBC clutch rebuild kit including springs $130
> Stock axles $60 no CV's or boots for the pair
Stock Rear a Arms $100 for the pair
> Custom no fail seat brace $20 keeps the front of the seat from caving in on top of the carb and intake
> black seat in great shape $100
Black Seat with good pan but ripped cover $60
Red seat cracked pan small rip incover $40
> 42 mm FCR carb bored by racers edge in Tucson $300 including twist throttle 50 miles on it
> Pulser coil $30
> Custom intake and air box with 3 huge new K&N air filters $100 KMS Dyno showed 5hp gain with just this
Stock Undamaged Camshaft $50
> Elka stage 4 freshly rebuilt long travel front shocks $800 with shock covers 2 shocks
> Rear stage 4 freshly rebuilt long travel shocks $600 2 shocks shock covers
> Custom extended plus 2 long travel rear A arms less than 50 miles on them $400 including rear extended axles and CV's and boots Built by max Hernandez a pro desert racer out of Phoenix
> Custom long travel power coated gray front plus 2 a arms built by FST fabrication out of Phoenix $500 including spindles and brake calipers and extended brake lines
> Or the entire long travel front and back set up for $1800 including extended ss brake lines, shocks
> Rear hubs carriers with new fag bearings $ 50 each
> Rear center hub with welded sprocket lol $175 this has the grease zero mod already done and upgraded main bearings and includes the brake rotor
> Front Honda bolt pattern LSR hubs with tapered bearings $200 including rotors
Rear brake master cylinder $50 complete rear brake pedal to caliper $100
Front Brake master cylinder $50
> Electrical harness including switch $100 each (2) of these
Starter $50
Freshly rebuilt crank after melt down by crank works, Falicon rod and welded pin and AC bearing mod $400 like new ZERO hours
Blown motor $200 AC bearing Mod done to the cases Includes cylinder, clutch , transmission internals ect.. , NO crank, cylinder head or starter motor
Head has been Ported, polished, +1 valves and Bench flowed by racers edge in Tucson Az that cost us $900 alone it is damaged and Will require rebuild $100 Update on motor, crank is Rebuit Hot rod balanced and welded rebuilt with Honda Ball bearings, does not need cases to go with asking $400 zero hours on it ,, the motor cases and head is in worse shape than I was orginally informed of , so with that I've add new photos and taking offers on the motor parts, the camshaft is usable as is cltuch and transmission are in good shape
All motor work can be Confirmed by Kelly at KMS performance 2823 N 36th Ave # 110 Phoenix, AZ 85009
(602) 442-4340 http://www.kmsperformance.com/
>
You may contact me anytime , e mail or by phone . text is best
Joe At 602-435-2230
>