Parts, Parts, Parts! New Prices

[jhtrx250r]

JP cool head 19cc dome $95
Cascade throttle cover (new) $25
Cascade case saver (new) SOLD
large case saver that also goes over the shifter $22
zink coated rear hubs $40
ESR or Pro cross 310 cool head dome pump gas 32cc (new) $50
Rad Valve with carbon fiber 3 stage reeds 02B , with spacer plate $80
zink coated 86-87 rear seat latch $30
Zink coated kicker $50
Zink coated exhaust flange $20
cascade billit water pump cover (used but nice) SOLD
blue anodized fat bar adaptors $20
RE zink plated 86-87 seat latch lever and spring $20
IMS folding shifter used $15
TM front chain guide (new) $35
zink coated rear disk hub $25
Billit USA 1 +2 degree timing advance plate (new) $45
Duncan Bar Clamp (red anodized)SOLD
steel braded throttle cable (used) for OE carbs $15
Zink coated rear caliper holder $25
Black OE 1986-87 rear motor mount nice $20

Prices with out shipping, I use flat rate usps boxes you know the prices

If you see something you want But want to pay less, shoot me a offer, No worries if I dont like it Ill say no.

email me at jhtrx250r@yahoo.com

[jhtrx250r]

FMF gold series fatty and silencer, Very little use. no dents or dings, the usual rub marks from the tie rods.
Very nice email for expandable pics
$189 plus shipping

[jhtrx250r]

pipe front view, flash makes it look funny pipe is what fmf calls show chrome and its in great shape, silencer was polished

[jhtrx250r]

rear 1988-89 DG alloy bumper $25
Front OE bumper off a 87 powder coated semi gloss black $25
K&N air filter good shape $25
Front rotor guards 86-87 $20
Prices with out shipping these may need to go ups?

[jhtrx250r]

clutch side covers no damage off 1987 fit 1985-87 $60 ea.
Stator covers fit all years $25ea.
water pump covers fit all years $20ea.

shipping extra.

none of these parts have any damage but could use paint , powder coat or polish?

shipping would most likly be ups on these as well

[jhtrx250r]

Rear OE take off carrier from a 1988
fits 86-89 very nice resto quality no damage good bearings $65

[jhtrx250r]

another

[jhtrx250r]

last one

[jerorski]

i'll take the duncan clamp and cascade water pump cover, let me know what you think about the 330cc top end .

[jhtrx250r]

Jerorski sounds good, I never got the pics of your 330 top end? Did you send them to the right email? You don't happen to have a 310 do you?

[jerorski]

i will re send the pics, put my name on the red clamp and cascade water pump cover.

[jhtrx250r]

Jerry ill hold them for a day or so I have another buyer ready to buy the clamp.
Are you sure you have the right email?
It's jhtrx250r@yahoo.com

[jerorski]

i resent the pics of the top end, did you get them,lmk by phone, or i will pay for the clamp and waterpump cover and we can work it out when you get the pics,lmk

[jhtrx250r]

Jerry, I got 1 pic of the front , can't tell much from that so at this point I would say I'm not interested, from the head it looks like 1st gen pro cross , I sent you a reply via email I think with out a lot mote info and better pics I'm going to have to pass on that cylinder.
If you want the clamp and water pump cover you have my pay pal , send it as a gift , put your shipping info in the coments it will be in the mail the next day.

[jhtrx250r]

Cascade water pump cover and Duncan bar clamp sold!
Thanks jerry if I save any money on shipping I will refund it back to you!
Also you did not send me your address, I am ready to ship just need your address, text it to me if you like you have my #
Thanks James.

[jhtrx250r]

The cascade case saver is sold as well!
Thanks Jerry!
In the mail tomorrow

[crlt250r]

Email sent.

[bradenc19]

do u have a 86 87 front seat bracket if so how much