DRX rolling chassis (standard travel)

[GetOut&Ride]

Full DRX rolling chassis (frame, dual a-arms, swing-arm) with no signs of any cracks/splits or concerns of any kind as it's never been rolled/wrecked... was a great reliable chassis that helped him learn to ride the last few years.

To be a full roller it would have stock handlebars, OEM steel rims, OEM tires, OEM red coil shocks, disc brakes/calipers all the way around (connected to front brake lever on handlebars, rear footbrake lever to rear caliper).

This would have the black stock plastic (no cracks, major damage just normal use scuffs on rear fenders where MX boot buckles rub) and stock seat (no rips or tears).

Again, this is just a rolling chassis as the motor, pipe, electrical, throttle cables, carb, etc. will all be moved to the long travel setup.

The OEM axle snapped last year so I replaced with a dominator axle, so haven't decided yet if I sell this with the dominator axle on it or buy a stock one and keep the dominator (long travel setup one I'm looking at already has a dominator on it as well).

Asking $1000 or make reasonable offer (for right price I'll leave the $240 XFR bolt on nerfs on it and leave the $380 dominator axle on it)... whittle me down and I'll carry those pieces over to the next machine or sell seperate.

Drop in a 50motor and be riding!

Can take/send pictures if you like just PM me

[JustinBoots]

Where is Hearland and can you send me pics to justin.foilkers@gmail.com? Also is this a LC frame or AC frame and what year?

[GetOut&Ride]

I'm located in Iowa

The bike was an air cooled, but it has the mounts for the radiator (chassis/frame is universal).

[JustinBoots]

Originally posted by GetOut&Ride
I'm located in Iowa

The bike was an air cooled, but it has the mounts for the radiator (chassis/frame is universal).

Ok too far out for me. Guess some of the frame are different though because my current air cooled 2007 frame doesn't have the tabs on the bottom for the lower radiator support bracket.

[oldironmn]

I would be interested in the nerf bars if you want to sell them seperate

[GetOut&Ride]

Price is reduced to $750

Here's the updated situation/description that is reflected in the price reduction

- Axle is now stock/OEM

- During tear down I found the frame is cracked (top frame tube just in front of where the swing arm bolt frame tube meets the top horizontal frame tube, behind the seat rubber grommets)

- During tear down I found the XFR nerf bars have a chip out of the foot peg teeth on one side and the inside loop (that holds the webbing) on both sides is flattened/pinched

- Son decided to go to polished aluminum rims instead of black aluminum this year, so have 4 black aluminum wheels with good tires mounted (details below)


So for $750 here is what you get (description in this post and then I'll post a series of pictures) as a full rolling chassis (bolt motor, electrical and go):
- Full frame (currently ungussetted, but in need of a repair per above), including OEM front bumper
- OEM standard travel red coil over shocks
- OEM dual A-arm front end
- OEM tie rods
- OEM steering stem
- OEM handlebars
- OEM gas tank, lines, fuel shutoff pecock
- OEM full disk brake system (front right hand brake, rear left hand brake, all 3 calipers, lines, etc.)
- Black XFR nerf bars (note the info above, that these are not perfect)
- OEM swing arm (including carrier bearings, adjusting bolts, etc.)
- OEM axle
- OEM rear sprocket mount and 32 tooth rear sprocket
- OEM hubs/spindles
- Full set (4) black aluminum rims
- Razr MX 19" rubber on front that aren't showing any significant signs of wear
- 18" Carlisle Snow Hogs, I'd describe as 75%... still showing groove in center of dog bone shaped tread
- OEM black plastic (complete, never been cut, no cracks... just minor scuffs)

A full roller for less than price of just a new main body frame

[GetOut&Ride]

Pic

[GetOut&Ride]

Pic2

[GetOut&Ride]

Pic3

[GetOut&Ride]

Pic4

[GetOut&Ride]

Pic5

[GetOut&Ride]

Pic6

[GetOut&Ride]

First pic of crack

[GetOut&Ride]

Second pic of crack

[GetOut&Ride]

Third pic of crack

[GetOut&Ride]

Body Plastic 1

[GetOut&Ride]

Body Plastic 2

[GetOut&Ride]

Body Plastic 3

[GetOut&Ride]

Nerf 1

[GetOut&Ride]

Nerf 2

[GetOut&Ride]

Nerf3

[GetOut&Ride]

Nerf4

[edwardsp&b]

If you were closer to Ga I would pick that up from you. You coming to the first Nat at Aonia? Let me know
Bryan

[RCR_531]

He has friend that will be at the First National event and they may even be in the area on the weekend of Feb.25-27

[GetOut&Ride]

The rolling chassis has been SOLD!

Thanks EX Riders Community!

Have fun, ride hard, be safe...