RayWilt
08-31-2011, 07:22 AM
Just cleaning out the garage I have a 86 cylinder with a 295 sleeve installed. It just needs to be ported and be taken to the final bore. The 330 cylinder I have is ported by trinity for top end and also has the vortex swirles cut in the head. This cylinder does how ever leak coolant betweek the sleeve and jug down to the exhaust port. I have been told that it can be fixed. Cylinder was very fast before it leaked.
I also have alot of stock parts. Most of them are 86. There is an almost complete bottom end. My one buddy took one of the gears from the tranny dont rememer wich one. The one case has a hole between the crankcase and counter balancer. I also have stock arms, spindles, front and rear calipers, stock carbs, and alot of other odds and ends. I have a old set of factory white plactics no cracks in them but they do show there age and need a real good wet sanding to get back in good shape. The fronts were cut down.
I will ship the the 2 cylinders but the rest of the parts if someone is interested in the pick them up local as a total lot.
I have pics of all the parts and cylinders.
Cylinders $125 a piece
parts $200 for everything
250r Parts
Crank cases (1) left side (2) right sides
Transmission 86 missing a gear
1 complete clutch assy.
Pressure plate
Inner clutch hub
2 counter balancers
Stator cover
Clutch cover
2 Weisco pistons (piston only no rings, wrist pin)
Cylinder, with head and read cage (needs resleeved)
2 stock carbs
36mm pwk carb
Reed spacer
Factory crank ( condition unknown would rebuild to be safe)
2 rear shock ( 1 is a atc shock)
2 air filters
3 outerwears
Gaskets ( head gaskets, base, reed, water pump clutch cover, and stato cover)
Rear suspension link
Rear caliper
Rear caliper housing
Chain guards
2 cdi
Stator and flywheel
2 counter balancer holders
4 kick starters
Rear axle lock nut
Throttle housing
Front calipers and brake lines
Frame brace (upper motor mount)
Rear brake hub
Air box
2 air box lids
Foot pegs
3 shift levers
Bearing carrier ( need new bearings)
2 air intakes boot ( between carb and airbox) 1 86 and 1 88
2 sets radiator shrouds
86 arms complete
86 spindles
86 front hubs with rotors
Tie rods with ends
88 arms
Factory tool box with lid
Coolant over flow
Rotors
Air snorkel
Fender brackets
Rear brake plate
Sprocket many sizes( Have more not pictured brand new if interested)
Front white fenders cut
Blue hood
White rear fenders
I also have alot of stock parts. Most of them are 86. There is an almost complete bottom end. My one buddy took one of the gears from the tranny dont rememer wich one. The one case has a hole between the crankcase and counter balancer. I also have stock arms, spindles, front and rear calipers, stock carbs, and alot of other odds and ends. I have a old set of factory white plactics no cracks in them but they do show there age and need a real good wet sanding to get back in good shape. The fronts were cut down.
I will ship the the 2 cylinders but the rest of the parts if someone is interested in the pick them up local as a total lot.
I have pics of all the parts and cylinders.
Cylinders $125 a piece
parts $200 for everything
250r Parts
Crank cases (1) left side (2) right sides
Transmission 86 missing a gear
1 complete clutch assy.
Pressure plate
Inner clutch hub
2 counter balancers
Stator cover
Clutch cover
2 Weisco pistons (piston only no rings, wrist pin)
Cylinder, with head and read cage (needs resleeved)
2 stock carbs
36mm pwk carb
Reed spacer
Factory crank ( condition unknown would rebuild to be safe)
2 rear shock ( 1 is a atc shock)
2 air filters
3 outerwears
Gaskets ( head gaskets, base, reed, water pump clutch cover, and stato cover)
Rear suspension link
Rear caliper
Rear caliper housing
Chain guards
2 cdi
Stator and flywheel
2 counter balancer holders
4 kick starters
Rear axle lock nut
Throttle housing
Front calipers and brake lines
Frame brace (upper motor mount)
Rear brake hub
Air box
2 air box lids
Foot pegs
3 shift levers
Bearing carrier ( need new bearings)
2 air intakes boot ( between carb and airbox) 1 86 and 1 88
2 sets radiator shrouds
86 arms complete
86 spindles
86 front hubs with rotors
Tie rods with ends
88 arms
Factory tool box with lid
Coolant over flow
Rotors
Air snorkel
Fender brackets
Rear brake plate
Sprocket many sizes( Have more not pictured brand new if interested)
Front white fenders cut
Blue hood
White rear fenders