wishmasstir
01-26-2011, 11:51 AM
Looking to sell outright or trade for a 450 mx quad ( yfz450 yfz450r 450r kfx450r ltr450 ) and 250r based quads/hybrids
1990 gmc c-1500 regular cab, short bed, 2wd with a 700r4 transmission. The odometer reads 160k. It has 3.42 rear gears with the factory open differential. I have many spare parts, including a spare driver side door and door panels, new carpet, new floor mats, spare dash. I had the bed off and starting using rust encapsulator eastwood sells on the chassis, so its already done up to the cab.
the good:
Truck currently has a set of kmc wheels on it as shown in the picture but I have a pair of 20x10 w/6" backspacing boyd coddington magneato rims for the rear
belltech 4/6 drop kit
Billet grill
clear corners
clear parking lights
tyc true hid conversion kit ($900 retail) ballast are built into the housings
Sport mirrors
Shaved the stake pockets, the rear roll pan, the antenna.
fully built 383 stroker long block with vortec heads and edelbrock vortec intake (needs carb)
hooker long tube headers
electric fans from ls1
I have a new set of catalytic convertors and a set of mufflers also
the bad:
the engine is on a stand right now
no carb
new exhaust will need made
I sold the bench seat out of it with plans of installing buckets
the ugly:
The passenger door will need painted to match, there is a matching door currently on the truck but I bought a set of full power doors to install and replace the passenger door due to a hefty dent.
The front fenders need painted to match (they are currently black, I put them on since the antenna is shaved and the wheel wells lips are rolled for tire clearance).
There are a couple rust bubbles over the rear wheel wells and cab corners starting
There is also a dent near the tail light on the passenger side.
I'm selling everything listed and many parts not listed as a project for $3500
Please only reply to wishmasstir@gmail.com
thanks,
Mike
1990 gmc c-1500 regular cab, short bed, 2wd with a 700r4 transmission. The odometer reads 160k. It has 3.42 rear gears with the factory open differential. I have many spare parts, including a spare driver side door and door panels, new carpet, new floor mats, spare dash. I had the bed off and starting using rust encapsulator eastwood sells on the chassis, so its already done up to the cab.
the good:
Truck currently has a set of kmc wheels on it as shown in the picture but I have a pair of 20x10 w/6" backspacing boyd coddington magneato rims for the rear
belltech 4/6 drop kit
Billet grill
clear corners
clear parking lights
tyc true hid conversion kit ($900 retail) ballast are built into the housings
Sport mirrors
Shaved the stake pockets, the rear roll pan, the antenna.
fully built 383 stroker long block with vortec heads and edelbrock vortec intake (needs carb)
hooker long tube headers
electric fans from ls1
I have a new set of catalytic convertors and a set of mufflers also
the bad:
the engine is on a stand right now
no carb
new exhaust will need made
I sold the bench seat out of it with plans of installing buckets
the ugly:
The passenger door will need painted to match, there is a matching door currently on the truck but I bought a set of full power doors to install and replace the passenger door due to a hefty dent.
The front fenders need painted to match (they are currently black, I put them on since the antenna is shaved and the wheel wells lips are rolled for tire clearance).
There are a couple rust bubbles over the rear wheel wells and cab corners starting
There is also a dent near the tail light on the passenger side.
I'm selling everything listed and many parts not listed as a project for $3500
Please only reply to wishmasstir@gmail.com
thanks,
Mike