1quadracer2
08-23-2010, 05:30 PM
This one is fast, fast, fast! The quad is race ready! This quad has been raced at GNC the last two years, about 12 weekends of racing. This sale will also include extra parts for the quad. Everything you see in the pictures will be sold with this unit. There are other smaller parts (nuts, bolts and screw type) parts that will be include as well but not shown in pictures.
The Quad: Frame is made by Lone Star and is based off the 250R. The front A-arms were built by KOQ as well is the rear swing arm, both are +2. Steering stem is built by KOQ with a Pro Taper handle bar. Front and rear shocks are Elka and currently set up for a 150# rider. Engine is a Honda CRF150 national race motor built by SCR with a UNI two stage air filters and a Outter wears pre-filter. Exhaust is a Pro-Circuit T-4. Radiator is a PWR over sized. .Front hubs, spindles, rotors and disks are from a Honda 300ex. Rear end consist of Honda brakes system from CRF250, carrier is Magnum dual roller with a Durablu X33 axel. AC front bumper rear grab bar and nerf bars. Drive system consist of front and rear sprockets by Rebal Gears and a DID Professional O-ring chain. Front wheels are ITP aluminum (4/110 bolt pattern) with ITP Holeshot MXR6 AT19x6x10 tires. Rear wheels are ITP aluminum (4/110 bolt pattern) with ITP Holeshot AT18x10x8 tires. Plastic is from Maier (Note: this plastic is set up so that it can be taken off in less than one minute!) Seat is from a stock Honda 250R, has a small wear hole on the left side. The spare parts are as follows:
1)Used rear set of Turf Tamers tire size AT19X9.5-8 w/ ITP aluminum wheels with a 4/110 bolt pattern.
2)Kids on Quads New steering stem
3)Kids on Quads new +2 rear swing arm
4)PC Racing stainless steel reusable oil filter for Honda CRF 150 motor
5)3- New NGK Cr8EH-9 spark plugs
6)3-New exhaust pipe gaskets for CRF 150 motor
7)1-New bottom steering stem bearing for a 250R
8)5- New pin bushings for brakes of a 300 or 400 ex Honda
9)4-New pin boot for brakes on a 300 or 400ex Honda
10)2- New exhaust flange nuts foe Honda CRF 150 motor
11)2-New rubber grommets for front plastic of a Honda 250R
12)9-New sprocket bolts for rear end of a Honda 300 or 400ex(10mm)
13)9-New flange nuts(10mm)Honda
14)2-New flange nuts(12mm)Honda
15) 1-new lug nut for 300 or 400ex Honda
16)3-New flange nuts(14mm)Honda
17)3-New DID Professional O-ring Chains(DID428V-120FB)
18)1-New 46TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
19)1-New 47TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
20)1-New 48TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
21)2-New 50TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
22)1-Used 46TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
23)1-Used 50TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
24)1-New 15TX428 countershaft sprocket for a CRF150 Honda
25)1-New 14TX428 Rebel Gear countershaft sprocket for a CRF150 Honda
26)1-New 14TX428 Renthal countershaft sprocket for a CRF150 Honda
27)1-Used 14TX428 Rebel Gear countershaft sprocket for a CRF150 Honda
28)1-New swing arm kit for Honda 250R
29)1-New Honda throttle cable
30)1-New Honda hot start cable for a CRF150 Honda
31)1-New Honda clutch cable for a CRF150 Honda
32)3-New UNI 2 stage POD filters(UP-6229AST)
33)1-Used UNI 2 stage POD filters(UP-6229AST)
34)5-New Outer wears Pre filters(20-1072-01, WR17-2952-675T)
35)1-New Front chain slide for Honda 250R
36)1-New Rear chain slide for Honda 250R
$9500 - also listed on eBay
If you are the lucky winner of this sale you will need to make arrangements for shipping or pick up as the seller will not ship this or any part of this sale. Good luck and happy racing!
The Quad: Frame is made by Lone Star and is based off the 250R. The front A-arms were built by KOQ as well is the rear swing arm, both are +2. Steering stem is built by KOQ with a Pro Taper handle bar. Front and rear shocks are Elka and currently set up for a 150# rider. Engine is a Honda CRF150 national race motor built by SCR with a UNI two stage air filters and a Outter wears pre-filter. Exhaust is a Pro-Circuit T-4. Radiator is a PWR over sized. .Front hubs, spindles, rotors and disks are from a Honda 300ex. Rear end consist of Honda brakes system from CRF250, carrier is Magnum dual roller with a Durablu X33 axel. AC front bumper rear grab bar and nerf bars. Drive system consist of front and rear sprockets by Rebal Gears and a DID Professional O-ring chain. Front wheels are ITP aluminum (4/110 bolt pattern) with ITP Holeshot MXR6 AT19x6x10 tires. Rear wheels are ITP aluminum (4/110 bolt pattern) with ITP Holeshot AT18x10x8 tires. Plastic is from Maier (Note: this plastic is set up so that it can be taken off in less than one minute!) Seat is from a stock Honda 250R, has a small wear hole on the left side. The spare parts are as follows:
1)Used rear set of Turf Tamers tire size AT19X9.5-8 w/ ITP aluminum wheels with a 4/110 bolt pattern.
2)Kids on Quads New steering stem
3)Kids on Quads new +2 rear swing arm
4)PC Racing stainless steel reusable oil filter for Honda CRF 150 motor
5)3- New NGK Cr8EH-9 spark plugs
6)3-New exhaust pipe gaskets for CRF 150 motor
7)1-New bottom steering stem bearing for a 250R
8)5- New pin bushings for brakes of a 300 or 400 ex Honda
9)4-New pin boot for brakes on a 300 or 400ex Honda
10)2- New exhaust flange nuts foe Honda CRF 150 motor
11)2-New rubber grommets for front plastic of a Honda 250R
12)9-New sprocket bolts for rear end of a Honda 300 or 400ex(10mm)
13)9-New flange nuts(10mm)Honda
14)2-New flange nuts(12mm)Honda
15) 1-new lug nut for 300 or 400ex Honda
16)3-New flange nuts(14mm)Honda
17)3-New DID Professional O-ring Chains(DID428V-120FB)
18)1-New 46TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
19)1-New 47TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
20)1-New 48TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
21)2-New 50TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
22)1-Used 46TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
23)1-Used 50TX428 Rebel Gear rear sprocket for a 300 or 400ex Honda
24)1-New 15TX428 countershaft sprocket for a CRF150 Honda
25)1-New 14TX428 Rebel Gear countershaft sprocket for a CRF150 Honda
26)1-New 14TX428 Renthal countershaft sprocket for a CRF150 Honda
27)1-Used 14TX428 Rebel Gear countershaft sprocket for a CRF150 Honda
28)1-New swing arm kit for Honda 250R
29)1-New Honda throttle cable
30)1-New Honda hot start cable for a CRF150 Honda
31)1-New Honda clutch cable for a CRF150 Honda
32)3-New UNI 2 stage POD filters(UP-6229AST)
33)1-Used UNI 2 stage POD filters(UP-6229AST)
34)5-New Outer wears Pre filters(20-1072-01, WR17-2952-675T)
35)1-New Front chain slide for Honda 250R
36)1-New Rear chain slide for Honda 250R
$9500 - also listed on eBay
If you are the lucky winner of this sale you will need to make arrangements for shipping or pick up as the seller will not ship this or any part of this sale. Good luck and happy racing!