tinners with stabilizer???

[logant14]

can you put a stick stabilizer on with these scoops? i dont think a cnc would work, would it? thanks maybe put up a pic if you have one

[Ryan'07400ex]

Yea tinners wont work with my cnc :(
However I could of cut some of it off but i thought it wouldn't be very sturdy so i took the tinnner scoops off.

[tri5ron]

Scoops (not Tinners), CNC Stabilizer, 450r front shocks with rezzies to the rear.
works beautifully together.
(but yes, I did minimally trim the lower sections of the scoops, to clear the rezzies)

http://i111.photobucket.com/albums/n148/tri5ron/03%20400ex/IMG_0151.jpg

http://i111.photobucket.com/albums/n148/tri5ron/03%20400ex/IMG_8840.jpg

http://i111.photobucket.com/albums/n148/tri5ron/03%20400ex/IMG_8257.jpg

[Ryan'07400ex]

That looks nice, I wish I would of tried it before I sold them.

[clemsonteg]

Originally posted by tri5ron
Scoops (not Tinners), CNC Stabilizer, 450r front shocks with rezzies to the rear.
works beautifully together.
(but yes, I did minimally trim the lower sections of the scoops, to clear the rezzies)

http://i111.photobucket.com/albums/n148/tri5ron/03%20400ex/IMG_0151.jpg

http://i111.photobucket.com/albums/n148/tri5ron/03%20400ex/IMG_8840.jpg

http://i111.photobucket.com/albums/n148/tri5ron/03%20400ex/IMG_8257.jpg

Doesn't look to be like the stabilizer would cause a problem with the scoops, shocks are a different story but you handled that.

[beags86]

hey ron, how do you like that stabilizer, i am thinking about getting a few for my pair of 4hundys??

[tri5ron]

Originally posted by beags86
hey ron, how do you like that stabilizer, i am thinking about getting a few for my pair of 4hundys?? Sorry for the late responce. I think it is about the best "Bang for your Buck" stabilizer you can get.
Here's a LOooooonnnggg thread on them, from when they first came to our attention. It's a fun read. enjoy...
http://www.exriders.com/vbb/showthread.php?s=&threadid=349366

[smorris1]

may be a dumb question but I never did get what a steering stabilizer does. haha Wouldnt it make the bars harder to turn?

[guenther]

The bars are only harder to turn if you have the stabilizer cranked up all the way. This is one of the best mods you can do in my opinion. I feel safer knowing my arms aren't going to get ripped out of their sockets when I catch the side of something hiding in the gunch.

[beags86]

Originally posted by tri5ron
Sorry for the late responce. I think it is about the best "Bang for your Buck" stabilizer you can get.
Here's a LOooooonnnggg thread on them, from when they first came to our attention. It's a fun read. enjoy...
http://www.exriders.com/vbb/showthread.php?s=&threadid=349366

no worries ron, i remember reading the thread a while back when it was on top of the board. and i couldn't rememeber what every one had said about it so i just asked.

[clemsonteg]

So Ron would the stabilizer clear the air scoops without the 450 shocks?

[tri5ron]

Originally posted by clemsonteg
So Ron would the stabilizer clear the air scoops without the 450 shocks? yes, but you have to turn the tail light upside down first.

[clemsonteg]

No problem, I have to do that when I change the muffler bearings next week anyways :)