robyone
05-21-2010, 09:53 AM
Up for grabs is my 88 XC project...
88 frame= fully gusseted & PCed
Bottom end only (you supply top end)=
Completely rebuilt, every bearing and seal is brand new, aftermarket clutch..this was built from a mint ATC motor that I got on ebay years ago, so it's a short rod with mint tranny.
suspesion= triple rate TCS front & rear set up for a 200 to 250# rider...very little time on these.
A arms= Janseen +1 +1 forward with fresh heim joints.
swing arm= Houser 88 length.
Carb.= 38mm mikuni tmx
pipe= black paul turner ''trx race'' mid range.
stem= +1 chrome houser
Bars= renthal fat bars with billet clamps.
throttle= moose billet thumb throttle
levers= ASV unbreakable.
plastic= white OEM, fronts are in great shape with og. 86 decals and rears are in good shape with a small stiched crack.
reeds= boysen rad valve...needs new reeds.
tires & wheels= powder coated black champion bead locks with 90% hole shot GNCC's.
brakes= brand new rotors and pads, newer calipers front and rear with braided lines.
pegs= roll design non kick ups with PCed black roll heel guards.
axle= brand new RPM +1 with brand new tapered bearings and anti fade.
This has been sitting in my garage for the past 3 years unfinished, all it needs is a top end and a set of reeds and your riding. every bearing, seal brake pad and bushing is brand new with 0 rides.
Looking for $3200.00...quad is located in Morgantown, WV. email works best for me...roby.rollison@gmail.com
http://i4.photobucket.com/albums/y142/robyone/250/photo5.jpg
http://i4.photobucket.com/albums/y142/robyone/250/photo6.jpg
http://i4.photobucket.com/albums/y142/robyone/250/photo7.jpg
http://i4.photobucket.com/albums/y142/robyone/250/photo8.jpg
http://i4.photobucket.com/albums/y142/robyone/250/photo.jpg
88 frame= fully gusseted & PCed
Bottom end only (you supply top end)=
Completely rebuilt, every bearing and seal is brand new, aftermarket clutch..this was built from a mint ATC motor that I got on ebay years ago, so it's a short rod with mint tranny.
suspesion= triple rate TCS front & rear set up for a 200 to 250# rider...very little time on these.
A arms= Janseen +1 +1 forward with fresh heim joints.
swing arm= Houser 88 length.
Carb.= 38mm mikuni tmx
pipe= black paul turner ''trx race'' mid range.
stem= +1 chrome houser
Bars= renthal fat bars with billet clamps.
throttle= moose billet thumb throttle
levers= ASV unbreakable.
plastic= white OEM, fronts are in great shape with og. 86 decals and rears are in good shape with a small stiched crack.
reeds= boysen rad valve...needs new reeds.
tires & wheels= powder coated black champion bead locks with 90% hole shot GNCC's.
brakes= brand new rotors and pads, newer calipers front and rear with braided lines.
pegs= roll design non kick ups with PCed black roll heel guards.
axle= brand new RPM +1 with brand new tapered bearings and anti fade.
This has been sitting in my garage for the past 3 years unfinished, all it needs is a top end and a set of reeds and your riding. every bearing, seal brake pad and bushing is brand new with 0 rides.
Looking for $3200.00...quad is located in Morgantown, WV. email works best for me...roby.rollison@gmail.com
http://i4.photobucket.com/albums/y142/robyone/250/photo5.jpg
http://i4.photobucket.com/albums/y142/robyone/250/photo6.jpg
http://i4.photobucket.com/albums/y142/robyone/250/photo7.jpg
http://i4.photobucket.com/albums/y142/robyone/250/photo8.jpg
http://i4.photobucket.com/albums/y142/robyone/250/photo.jpg