250r/400ex partout....continued...

[michaelopfer]

i'm starting a new thread cause my older one has 8 pages, and not many people veiwing it lately... so here it is.
can get pics upon request..
there are some pics on the old thread. at http://www.exriders.com/vbb/showthread.php?s=&threadid=429396&perpage=10&pagenumber=4




i still got,
-all the mounts
-radiator
-front brake calipers
-front spindles
-frame
-subframe

-front tires....not wheels
-stock 400ex swing arm, with good pivot joint bearings
-rear bearing carrier, aftermarcket, but not sure on the brand. bearings are good
-rear hubs
-whole rear brakes
-nerfbars
-air box
-gas tank
-38mm kehin pwk carb, no cable...
-+4 stroker top end, fresh dune port, and bore. New piston and rings, with gaskets

and the anolog pvl ignition..

i probly got more laying around, just can't think of anymore. just ask

i have sold:
-motor
-steering stem
-wiring
-rear rims and tires
-front rims
-hood
-a arms
-shocks
-axle
-bumper
-handle bars
-throttle assembly
- front hubs and rotors

thanks

[bullett]

Sent you a pm

[michaelopfer]

pm'd back.


can take paypal.

[bullett]

sent another

[bullett]

Your inbox is full. I just sent payment. Thanks man

[michaelopfer]

yea, got it cleaned out now... thanks, and i'll get that out tomorrow.

[supraloud84]

do you have a good valve cover you want to sell?

[michaelopfer]

yes, actually i do... 50$ seems to be a good price for that..

lmk..

[supraloud84]

$50 shipped?

[1dirty400ex]

still got nerfs? how much shipped to 37087

[bobizzle]

pm'd

[michaelopfer]

$50 shipped?

well,, i am thinking i wanna keep that motor together incase i feel like rebuilding it.. thanks for the interest though.



still got nerfs? how much shipped to 37087

i have someone already going to buy them. if that deal falls through, your next in line..

thanks.

[jlschneider]

pm'd about the uni filter.

[k7mm]

PM sent.

[michaelopfer]

bump

I think I have the bearing carrier, nerf bars, and swing arm sold, just waiting to get pics and shipping quotes.. i thought someone wanted the radiator, but i cleaned my mail box and accidently deleted the message from him. if your reading this, shoot me another pm and we can probably work something out...

thanks..

[michaelopfer]

bump, carb sold...

[michaelopfer]

bump, swing arm sold..

quick list of what i got yet
front master cylinder w/ lever
frnt extended stainless steel brake lines
frame
sub frame
linkage
rear bearing carrier
front tires
gas tank
air box
mounts for 250r in 400, engine and radiator
radiator w/cap

pvl ignition for 250r

+4mm stroker top end-250r.

i probly got more, just can't think at the moment,, shoot me a resonable offer, and more than likely it's yours,
thanks for your time.

[droppedmazda]

how much for the carrier

[michaelopfer]

the bearings are still good, it is an aftermarket one with a grease zert on it.. it might be a dual row, but i don't know for sure.. don't really know what to ask on it, any resonable offer will do..
thanks.

[droppedmazda]

pm sent

[nyceguy01]

pm sent

[LT250RMan]

If I buy the 250R mounts, what do I all need to fab up on the frame besides the radiator mounts ??

[michaelopfer]

I actually have some radiator mounts that i was throwing in with the motor mounts i have already. there not pretty but they work. it sets the radiator offset to clear the exhaust and open the cap with it all assembled.

i have the front 2 "A" mounts

the spacers for the swing arm to line up the chain

the stock 250r rear motor mount braket that the pivot bolt goes through.

and i have a headstay mount i made out of a 400ex rear link peice.. i cut off the ear off of an old 400ex frame and welded it on the top rear of new frame. i cut the ear off so you can weld it on your frame if youd like.. the guy i bought it from just used the rear 2 and the front. but i didn't like that so I did it that way.

I did have 2 bars i made for the rear mount, but i forgot to get it off the motor before i sold it.:rolleyes:

so if you bought all the mounts and wanted to do it the way i did, all you would have to do is weld that ear for the headstay, and make some sort of brakets for the very bottom mount.. thats it, the rest should bolt on.. the exhaust is a tight fit, another guy on the forum shorten his to fit, but i used this old esr trx5 pipe, and didn't have any clearence problems.
edit: the carb is also a tight fit, because of were the intake boot is coming out of the 250r engine.. just finesse it allittle bit and it all goes together good.

never really seen any of these mounts sell, so i don't really know what to ask. i paid 50$+ship for the front 2 "A" ones already done up, and the rear 250r mount and spacers, but the spacers i never got.. now i've added the headstay and including the spacers, along with misc. bolts and the radiator mounts..
all i really want is 50$ +shipping just so i can get my money back on em'.

i can try to get pics tomorrow if you want.

thanks.

[michaelopfer]

bump, sold the carrier.

[afterchucker]

How much for the pvl?

[michaelopfer]

man, honestly.... I'm pretty hard up for some money.. so, make me an offer, and i'll probably take it.. I have no use for this, and not too many have asked about it..

it is a anolog one....didn't know if you caught that or not..

i have some pics somewhere, but i can't seem to find them... i'll run over and snap a few off for you..

thanks for the interest..

[hondaracer199]

do you still have bearing carrier, rotor and hub, rear master cylinder?

[michaelopfer]

I have the rear brakes, but i've already sold the rear bearing carrier,.. i'll get some pics of that aswell..

[afterchucker]

How about $100 bux for the pvl assuming it is complete?

[PaRedneckRiders]

do u still have the hood that was on the 400ex plastic, the carbon fiber i think it was quadtech

[michaelopfer]

ok, I finally got some pictures of the pvl and the rear brakes... but, my computer doesn't seem to want to read the memory card to put them on..




How about $100 bux for the pvl assuming it is complete?

It is complete minus the puller.. the middle rotor has seen it's better days(has some scratches, looks like the guy had a crank bearing go out.), but the guy i bought it from told me it would work. but i cannot garentee this, cause i haven't ever put this on my quad. He also said he had bought all brand new electronics for it.. I paid 150 for it, but i thought it had the puller with it. i'll take $80 plus shiping cause of it not having a puller and because of the condition of the rotor.. It's not absolutely terrible.. just very noticeable.lol.
i'll try to get them pics on the computer tom. mabey try another if i have to..





do you still have bearing carrier, rotor and hub, rear master cylinder?

I did get some pics of that aswell.. but again. my computer is bein a *itch and not leting me pull them off the camera.

will get them up as soon as i can..






do u still have the hood that was on the 400ex plastic, the carbon fiber i think it was quadtech

sorry, the hood was the first thing to go.. it was one of them off ebay..lol.. bought it a few years back, so not sure on brand, but i know it wasn't a quadtech.lol

[afterchucker]

Ill take the PVL off your hands.

[michaelopfer]

^replied to your pm...

[michaelopfer]

still working on them pics of the rear brakes for you hondaracer199... i'm gonna go over to a friends house and borrow his comp. to put the pics on..
thank you..

[hondaracer199]

sounds good, thanks man

[afterchucker]

paypaled you $88 bux for the pvl and shipping to ks. if 8 bux for shipping is not enough let me know.

[mrowe]

I need a 250r rear caliper and stay...got one left?

[hawaiianbasshed]

I'm 90% sure I'll take the top end. what size is the bore stock? I'm guessing like a 265 or something slightly bored stock cyl? also, you call it a top end, does it include a head to work with the stroker? I hear they need a rechamber or spacer or something? never ran a stroker and looking to do my 1st :D

any and all details you could tell me about it would be great.

can you get pix of it and the PWK? I pm'd u my cell number for pix, you can text me there as well. lmk a price on the PWK as well! thanks!

Tom

[michaelopfer]

I need a 250r rear caliper and stay...got one left?

lol, i never had one, just 400 frame stuff, and 250 motor stuff..


still working on getting pictures up... i'm gonna go and either find a cable, or go buy a new camera... we'll see...

[michaelopfer]

Hilol

[michaelopfer]

Hi

[afterchucker]

Hey Michael, That PVL ignition arrived.. Thanks for packing it well and shipping it fast.. It arrived in the condition you described or maybe better. Works perfectly

[levi624]

Got a starter for a 02 400ex.