project cr Monster in progress

[buck440]

well i'm finally building my dream bike. it's an 01 cr250r. it's gunna rep the Monster brand. tooo many mods to list but ill show you a few.

[buck440]

no more plastic ignition cover:macho

[buck440]

shiny

[buck440]

snatch shot

[buck440]

the best front and rear.

[buck440]

pro taper clamps...OMG i loovee them

[buck440]

my wheels from rad...monster colored lol.

[buck440]

graphics...it's going to be all white plastics.

[One_Bad_400]

looks good man, anything done other then pipe for the motor?.

why rep monster? unless someone is helping me out or payin me. i rep myself :D

[jcs003]

those cr's rip. get some porting done too.

[Brad77]

I love those early cr250s like the 01 and 02. Strong and smooth power. Yours is gonna look sick with those graphics and rims.

[buck440]

Originally posted by One_Bad_400
looks good man, anything done other then pipe for the motor?. next week the motor is being shipped to pro circut for porting and a local shop is revalving the suspension. i personally think the motor is scary fast as it is so i'm just trying to leave it stock besides porting, reed valve, and exhaust.

[133tmf]

man im diggin those rims gonna b NASTY !!!!

[buck440]

my main goal it to have monster energy put it up on their site somewhere if possible.

[KXRida]

Bike will look good.

To add to the thread here's my monster kxf...

http://i191.photobucket.com/albums/z152/Rmrider125/kxf6.jpg

http://i191.photobucket.com/albums/z152/Rmrider125/kxf7.jpg

[jcs003]

Originally posted by buck440
next week the motor is being shipped to pro circut for porting and a local shop is revalving the suspension. i personally think the motor is scary fast as it is so i'm just trying to leave it stock besides porting, reed valve, and exhaust.

if the porting is done well it make smooth out the power and build it up faster.

[buck440]

dang kxrida. one good looking bike. i hope the power is a little smoother as i came from a 400ex to this and its just flat out scary lol.

[jcs003]

i went from a warrior to a banshee to a 400ex to a 250r.lol

wish i would of got the 250r in the first place.:(

but i used to cruise around on my friends yz250 and that thing was just crazy fast. it would pull wheelies going 40+ mph.

[rpfeifer11]

I just sold my 1997 cr250 yesterday which was basically the same thing. It was scary.

[trx310R#24]

hows the build coming?

[buck440]

got the rest of the white plastics on and the rotors on the wheels which are on the bike. my camera is dead but i'll try to get pics up soon

[buck440]

found the charger so i got the pics not the best

[buck440]

smoothing out the cast marks

[buck440]

removing this crap will improve flow significantly

[buck440]

sending motor out to max power for 265 big bore, port, and set up to run on alcohol or vp110, undecided.

[buck440]

some sexy wheels:blah:

[buck440]

sure asv bend forward but not up and down...might just give sunline a try cause these levers are not cheap! like my anti freeplay device on it lol

[KXRida]

I believe asv carries a warranty on them for so long. Call them and see about a replacement lever. Bike is coming along nice. If you're running alcohol better change all the tubing on your carb and possibly your reeds. Not to mention you'll probably need some carb work for alcohol. Having a bike that runs on race fuel is fun and all, but not practical for me any more unless I have two bikes, which I don't at the time.