FourWerks Carbon Hood

[Pappy]

Jay sent us down a few hoods to try out. One was for our KFX. Installation was simple and took less then 2 minutes!

Be sure to check them out at http://www.fwcarbon.com/

http://kenhill.smugmug.com/Other/3-15-Practice/BEA2771/811083898_6Z2ta-L.jpg

http://kenhill.smugmug.com/Other/3-15-Practice/BEA2786/811086441_9kX82-L.jpg

http://kenhill.smugmug.com/Other/3-15-Practice/BEA2807/811087506_eTv4t-L.jpg

[DEVINF450R]

would you like to get rid of that hood pappy?

[MtnEX]

Looks good.

[Pappy]

I cleaned this thread up, but retained a full copy for future reference.

It has also come to my attention that Fourwerxs doesnt make this style hood for the KFX any longer, but be sure to check them out for all your carbon fiber needs.

(BTW, when you see a moderator post a link to something, consider it allowed by the upper managment here. If you have an issue, try the PM function)

[MR4Engine202]

I like how it looks how hard was it to bolt on?

[yfzrider45]

What kind of rear rims are those pappy??

[Pappy]

MR4-installed easily. Lined it up, drilled two holes for the upper mounts and used Honda push pins

yfz- ITP Baja's . That set has been on probably 4 different quads and lord knows how much racing they've seen. I keep saying I will order some Hipers when these let us down but so far they have been a solid rim.

[yfzrider45]

haha niice, do all itp rear baja rims come with dual beadlock?? i'll buy those if you want??

[Pappy]

Baja' arent beadlocks, they are dual reinforced rims (rings welded inside the rim)

These arent for sale, but they should be readily available for purchase. Give Colby at C&D Racing a call

http://kenhill.smugmug.com/Other/Shift-Gear/DSC2586/837163291_F6uqT-L.jpg

[FW_cArBoN]

Thank you for the kind words Pappy! I wish you and Cody the best of luck this season! The quad looks great, and Cody is growing like a weed I see! I remember when he looked little on a 90!!!

Thanks, Jay:D

[yfzrider45]

thanks, you da man pap lol

[MtnEX]

Originally posted by Pappy
Baja' arent beadlocks, they are dual reinforced rims (rings welded inside the rim)

These arent for sale, but they should be readily available for purchase. Give Colby at C&D Racing a call

http://kenhill.smugmug.com/Other/Shift-Gear/DSC2586/837163291_F6uqT-L.jpg

Stellar picture quality/detail....

[MtnEX]

I see someone was doing some stomping around at Yadkinville!

How did you do?

Are your rears 20" or 21"?

[Pappy]

20's...but the GNCC's are really a tad smaller then 20

He did ok. Lost his brakes heading into the first turn and wrecked. Hit the woods dead last and worked it from there. Ran over some guy who checked up and stalled in a ditch....new fenders are ordered.

Not having the brakes hurt him all day but he managed 9th out of 27 and 66th out of 250 I believe. We need some new parts for sure...new rear skid plate as well especially for the next national, the one we have been running is trashed

[MtnEX]

Yeah, mine were dead 20's at the peak when off. After looking at my buddy's 21" rears I think we should have gone that route.... an inch wider and don't look much taller than a 20".

The finish was very good considering all that happened.

Weak brakes are a huge confidence killer, without even considering how much slower you must go.

[Sprks450r04]

looks like my TRP hood

[FW_cArBoN]

We have more of these hoods in stock now.

They now feature a mesh grill insert.

- Jason

[MtnEX]

Don't see them on the website...

[FW_cArBoN]

Updated - 2 in stock

[MtnEX]

I like the mesh grill for sure...

Would dig it solid with your logo in there also...


Question... does it retain the stock lights?

[FW_cArBoN]

Yes we have CNC cut holes for the indicator lights as well.

Thanks, Jay

[Hetrick Racing]

We are looking for a carbon fiber engine skid,I make the mount if you could make the cut plate.
Give me a call
Rich

[FW_cArBoN]

Pm box is full. Please email me: jay@fwcarbon.com

We can help you with the engine plate for sure.

[Hetrick Racing]

Thank You