PDA

View Full Version : Gncc Schoolboy Rebuild


HENTHORNJR
09-03-2009, 04:17 PM
We tore apart Braden's 300 ex after snowshoe,and are just about done with the rebuild. Should be completly done tommorow. Here are a few pics , will post completed pics tommorow.
HENTHORNJR
09-03-2009, 04:18 PM
pic 2
HENTHORNJR
09-03-2009, 04:19 PM
pic3
thomasgangross
09-03-2009, 05:20 PM
the quad looks great, list of specs too when done!
treadway47025
09-03-2009, 06:55 PM
Looking very nice. Cant wait to see specs and pics!
IRISH-RACER-14
09-04-2009, 02:12 PM
top it off by putting some 07 300ex plastics
HENTHORNJR
09-04-2009, 09:14 PM
It's done.
HENTHORNJR
09-04-2009, 09:15 PM
pic 2
HENTHORNJR
09-04-2009, 09:16 PM
pic 3
HENTHORNJR
09-04-2009, 09:17 PM
pic4
HENTHORNJR
09-04-2009, 09:17 PM
5
HENTHORNJR
09-04-2009, 09:18 PM
6
born2ride14
09-05-2009, 07:13 AM
Sick Quad man1 very nice build. Whats all done to the motor?
300ridr
09-05-2009, 06:36 PM
Freakin Sweet!!! You need to put a list of mods up.
HENTHORNJR
09-06-2009, 08:17 PM
Here's the mods.


MOTOR:
HP ATV National XC Engine
FCR Carb
Jagg oil cooler
Curtis Sparks exhaust

BODY:
Maier Plastics
FTR Graphics
Jettrim hump seat

CHASSIS:
JB Racing +2 Steering stem
Flexx bars
Works connection elite clutch perch
Acerbis uniko handguards
Spider grips
Houser 400ex +2 A-Arms
400 ex spindles and hubs
PRM Bumper and skidplate
AC grab bar
IMS ROLL footpegs
IMS ROLL 400ex heelguards
HP ATV +2.5 Swingarm (uses 450r carrier, hub, rotor, axle, skid plate, TM design works chain guide and roller)
14t front 36t rear gears
Elka elite shocks front and rear,Quadtech carbon fiber shock protectors.

TIRES and WHEELS:
ITP GNCC 22x7x10 front 21x11x9 rears
HIPER 4x1 sbl front dbl rear
Highland Powersports Hiper mod rings w/ carbon fiber mud plugs inside and out.
born2ride14
09-07-2009, 09:20 AM
Where did you get that oil cooler? I need the oil filter cover i already have the cooler
HENTHORNJR
09-07-2009, 09:54 AM
I got the oil cooler and cover from: www.setrabusa.com. I will see if I can find the part # as they have quit making these, but they still had several when I got this one.
treadway47025
09-07-2009, 02:46 PM
does that henderson swingarm company have a website?
HENTHORNJR
09-07-2009, 06:06 PM
I don't think they have anything about the swingarm on the website yet. Just give Larry a call.
treadway47025
09-08-2009, 04:10 PM
So I got some IMS pegs ordered today off good old ebay. Was there much you had to do to get the 400ex ims heelguards to bolt up? I have to have heelguards. Used to run without when younger until I ran over my leg going kinda slow in a tricky situation and cracked my shin bone and got a nice gash out of it as well.
HENTHORNJR
09-08-2009, 06:18 PM
It didn't take a lot, just had to trim a little off to get the peg bolts lined up and shorten and turn where it bolts to frame.
treadway47025
09-08-2009, 06:47 PM
Thanks for the info. Since my quad is just a trail quad I am sure it will never be anything like yours. Yours is very nice!
300ridr
09-10-2009, 08:36 PM
did u have to get extended brake lines for the a arms? if you did, where did you get them
HENTHORNJR
09-13-2009, 06:00 PM
Yes, they are extended, they are Streamline's and they came from Houser .
ATV403
09-13-2009, 06:04 PM
Is the motor bored or stroked?
HENTHORNJR
09-13-2009, 06:44 PM
Bored
sd1
10-23-2009, 02:14 AM
beautiful quad...one of the best 300 GNCC ready I have seen......what type of rev box are you running?
shiley55
10-23-2009, 09:40 AM
was the oil cooler you used the one for the 400ex or the 450r or was it a universal.
sameltoe
10-23-2009, 10:38 AM
very nice build!
rob_990
10-28-2009, 07:57 PM
thats the nicest 300 ive ever seen!
IRISH-RACER-14
10-29-2009, 02:45 PM
please vote for the 300ex in the quad of the month section. please. we are only one vote behind a beutiful 450r.
stuntin andy
10-30-2009, 11:54 AM
get some action shots in here!!
HENTHORNJR
03-12-2010, 07:27 PM
GNCC FL AND GA
HENTHORNJR
03-12-2010, 07:28 PM
MORE
HENTHORNJR
03-12-2010, 07:30 PM
1
HENTHORNJR
03-12-2010, 07:33 PM
2
stuntin andy
03-13-2010, 12:06 AM
thats uhh mazeing


love the bike dude
Gomer11
03-13-2010, 07:58 AM
is the frame and stuff powdercoated? or painted?
HENTHORNJR
03-13-2010, 08:09 AM
Powdercoated.
Dylan227
03-14-2010, 10:22 AM
How do you keep those white plastics so clean and stain free?
Arctic Cat Dad
03-14-2010, 05:09 PM
I don't know what he does. But I spray the whole quad down with sylicone spray. Or even wd-40. Makes it shine like new and a whole lot easier to clean.:D
HENTHORNJR
03-14-2010, 09:06 PM
The plastics are Maier and he use's SILKOLENE PRO PREP on it before the race.
etondaddy
03-15-2010, 05:37 AM
That's a nice lookin machine....I hope ours comes out that nice.


Mike Kozura
Pappy
03-15-2010, 07:18 AM
The quad is cool, but I give a ton of credit to the rider! That boy is haulin!!!!!

http://kenhill.smugmug.com/Other/Private-Gallery-2/BEA1302/810780672_nAnBA-O.jpg
etondaddy
03-15-2010, 07:26 AM
Great pic Pappy........... you boys all thawed out down there in by god WV.......lol


Mike Kozura
Pappy
03-15-2010, 10:48 AM
Yeah the snow is all gone here but I can still see it on the ridge above us. Now its all mucky and wet:p Its firewood time so we have been busy getting wood cut for next year, but the racing will be back on our minds this sunday at Rocket. I have to go cover teh GNCC but will be back...Cody can do the driving:D