EchoRocket
08-22-2009, 07:33 AM
Hello, You are looking at a 2004 YFZ450. This quad has the best of everything on it. Needs nothing. All chassis components are powder coated. I have receipts available
Here is a parts list:
CHASSIS:
'05 YFZ450 Frame Gusseted
Laeger ProTrax Front end (a-arms, spindles, clevis, tie rods)
Janssen Outlaw 2 swingarm/carrier
JB Racing +1 steering stem
JB 6 point subframe
RPM Dominator Axle
PEP Shocks Front and Rear Fronts are Compression adjustable, Rear is Comp and Rebound w/ long line to move resivoior up front.
Hardkor Engineering Front Hubs Honda Pattern
Precision Steering Stabilizer
PEP Chain roller relocator
Baldwin Motorsports pivot bolt
MOTOR:
'04 Cases w/ New Main Crank Bearings (old ones did not go out)
'08 Crankshaft (makes it a true 450)
Baldwin Motorsports Headwork, Port and Polish, Serdi valve job, ALL NEW VALVES shimmed by Mark Baldwin himself!
Baldwin Motorsports 13.5:1 compression piston
Stock Cams w/cam mod done
Curtis Sparks Pipe/Silencer
CV4 hoses
New Shift drum
Shift Forks and tranny gears were spec'd when rebuild was done.
New Clutch (Plates and Steels)
'06 Shifter
PEP EZ-PULL Clutch arm
TM Designworks Case Saver
Decompression Plug
CARB:
FCR 39MM
NCVQ NEEDLE (4th CLIP), GYTR FUEL SCREW 2 1/4 turn out 175 main, 45 pilot
INTAKE:
Curtis Sparks Racing ProFlow plate w/ 4 Curtis Sparks Foam air filters
ELECTRICAL:
'04 wiring, gutted by MUFFS MOTORSPORTS to get rid of the resistor kit.
Dirt bike killswitch / start button setup
TPS REMOVED
DynaTek Programable Ignition w/custom SX curve
MTR Battery Box w/Yusa YFZ battery
Gunnar Teather Switch
MISC:
HIPER Front 4+1 offset wheels on Maxxis Razr Cross tires
HIPER Rear 3+5 wheels on Maxxis Razr Cross tires
Quad Tech Seat cover on '04 foam, w/blue black cover
Quad Tech Hump Seat w/ extra foam w/ black seat cover both are in near new conditon
Quad Tech Plastic HP1 Hood w/ Baldwin Motorsports Background w/ free extra set of white back grounds
Blue Stock YFZ Plastics
Renthal 7/8 Jeremy McGrath bend bars
Works Connection Elite Clutch Perch
Sunline Gas tank Vent
Galfer Stainless sleel brake lines f/r
Gas Tank and Heat sheild have Heat tape on them to keep gas cool
Renthal Soft compound grips
Yamaha Throttle body
Yamaha Master Cylinder F/R
Stock Rear Hubs
Blingstar Iron Cross front bumper w/blue vinyl background
AC racing 250r propeg nerf bars 1" down 1" back
Stock '04 grab bar
Stainless steel Footpegs are sharpened w/ extra clean out added
White Bothers rear parking brake block off
I HAVE A TON OF EXTRA PARTS FOR THE MACHINE: including a wire harness, hardkor hubs, stock hubs, motor mounts ect.
SORRY FOR SUCH A LONG LIST!!! IM SURE IM FORGETING SOMETHING. ALOT OF TIME HAS BEEN PUT INTO THIS MACHINE TO GET IT WHERE IT IS. EVERYTHING IS PROVEN ON IT. IT HAS BEEN TAKEN CARE OF EXTENSIVELY. APPROX: 20 HRS on machine.
*THIS IS THE MINNESOTA STATE SUPERCROSS CHAMPIONSHIP WINNING MACHINE*
PRICE IS SET AT $6,500.00 well over $15K invested here
I AM IN MINNESOTA, MY # is 507-828-1233, email is c_borning@hotmail.com
THANKS FOR LOOKING!
Here is a parts list:
CHASSIS:
'05 YFZ450 Frame Gusseted
Laeger ProTrax Front end (a-arms, spindles, clevis, tie rods)
Janssen Outlaw 2 swingarm/carrier
JB Racing +1 steering stem
JB 6 point subframe
RPM Dominator Axle
PEP Shocks Front and Rear Fronts are Compression adjustable, Rear is Comp and Rebound w/ long line to move resivoior up front.
Hardkor Engineering Front Hubs Honda Pattern
Precision Steering Stabilizer
PEP Chain roller relocator
Baldwin Motorsports pivot bolt
MOTOR:
'04 Cases w/ New Main Crank Bearings (old ones did not go out)
'08 Crankshaft (makes it a true 450)
Baldwin Motorsports Headwork, Port and Polish, Serdi valve job, ALL NEW VALVES shimmed by Mark Baldwin himself!
Baldwin Motorsports 13.5:1 compression piston
Stock Cams w/cam mod done
Curtis Sparks Pipe/Silencer
CV4 hoses
New Shift drum
Shift Forks and tranny gears were spec'd when rebuild was done.
New Clutch (Plates and Steels)
'06 Shifter
PEP EZ-PULL Clutch arm
TM Designworks Case Saver
Decompression Plug
CARB:
FCR 39MM
NCVQ NEEDLE (4th CLIP), GYTR FUEL SCREW 2 1/4 turn out 175 main, 45 pilot
INTAKE:
Curtis Sparks Racing ProFlow plate w/ 4 Curtis Sparks Foam air filters
ELECTRICAL:
'04 wiring, gutted by MUFFS MOTORSPORTS to get rid of the resistor kit.
Dirt bike killswitch / start button setup
TPS REMOVED
DynaTek Programable Ignition w/custom SX curve
MTR Battery Box w/Yusa YFZ battery
Gunnar Teather Switch
MISC:
HIPER Front 4+1 offset wheels on Maxxis Razr Cross tires
HIPER Rear 3+5 wheels on Maxxis Razr Cross tires
Quad Tech Seat cover on '04 foam, w/blue black cover
Quad Tech Hump Seat w/ extra foam w/ black seat cover both are in near new conditon
Quad Tech Plastic HP1 Hood w/ Baldwin Motorsports Background w/ free extra set of white back grounds
Blue Stock YFZ Plastics
Renthal 7/8 Jeremy McGrath bend bars
Works Connection Elite Clutch Perch
Sunline Gas tank Vent
Galfer Stainless sleel brake lines f/r
Gas Tank and Heat sheild have Heat tape on them to keep gas cool
Renthal Soft compound grips
Yamaha Throttle body
Yamaha Master Cylinder F/R
Stock Rear Hubs
Blingstar Iron Cross front bumper w/blue vinyl background
AC racing 250r propeg nerf bars 1" down 1" back
Stock '04 grab bar
Stainless steel Footpegs are sharpened w/ extra clean out added
White Bothers rear parking brake block off
I HAVE A TON OF EXTRA PARTS FOR THE MACHINE: including a wire harness, hardkor hubs, stock hubs, motor mounts ect.
SORRY FOR SUCH A LONG LIST!!! IM SURE IM FORGETING SOMETHING. ALOT OF TIME HAS BEEN PUT INTO THIS MACHINE TO GET IT WHERE IT IS. EVERYTHING IS PROVEN ON IT. IT HAS BEEN TAKEN CARE OF EXTENSIVELY. APPROX: 20 HRS on machine.
*THIS IS THE MINNESOTA STATE SUPERCROSS CHAMPIONSHIP WINNING MACHINE*
PRICE IS SET AT $6,500.00 well over $15K invested here
I AM IN MINNESOTA, MY # is 507-828-1233, email is c_borning@hotmail.com
THANKS FOR LOOKING!