welder83
08-02-2009, 08:38 PM
For Sale 2003 Z400
I bought the machine new in 03 and I am the only owner. It has a Illinois title that i have in hand. Machine has been xc raced a handfull of times but mainly just a weekend toy. Very well maintained with new or in like new bearings all around.I do have a new complete set of wheel bearings and a new set of swingarm bearings i will throw in . ALOT of work done to it do to the fact that alot of my buddys xc race. Dont really want to get rid of quad but never have time to ride and just takes up room in garage.
CALL 618-292-0008
CAN EMAIL MORE PICS OF WHATEVER YOU WANT TO SEE
$3500 OBO SERIOUS OFFERS ONLY
Engine -
-stage 3 cams both intake and exhaust from lrd(web cam)
-weisco high compression piston(runs good on 93 octane but runs better on 110 and adds more snap thru the gears)
-full lrd exhuast system
-stock carb (but also have a 41mm edelbrock if interested)
-twin air filter
-new transmission in 06
-machine leaks a slight amount of antifreeze from bottom of water pump but could ride all weekend and never have to add any
-machine also leaks slight amount of oil from were the reverse cable goes into the side case. ive been told that it was a common problem and i personally have had it fixed 3 times it is about a 2 dollar gasket that goes bad.
Quad-
ac bumper
ITP C series wheels with itp holehots in front 23x7x10
stock wheels in rear with 20inch razers
*** i have hipers all around with razer 2 in front and razer backs( sold seperate if wanted)
ac front bumper
quad tech hood
prm grab bar
IMS foot pegs
dura blue adj. axle
good sprockets front and rear but may need new front due to the fact it was set up for 22's in rear
D I Dchain in great shape
maier plastic all around in great shape no cracks
full baja belly skid with side motor kick ups
prm swing arm skid
2005 frame that has been gusseted very well and powder coated(my job is a union welder and made gussets myself and went over all welds on frame)
steel braided brake lines all around
billet bar clamp
lonestar tie rods
magura hyd clutch(with steel braided line)
gripper seat cover with added fome for more comfort
roll design stem
bebe handle bars
works triple rate in front rebuilt and valved by derisi racing
ims oversized tank
1000 higher rev box
denton plus one swingarm with round style carrier
twin row carrier
elka dual rate with remote res. and elka linkage
has new sub frame but needs to be touched up with paint
wave rotors all around
twin air air filter with k&n stainless clamp(also have a like new extra air filter)
BRAND NEW maxxstart battery never had a ride on it
clutchs have less than 8 hours on them
I also have a few new sets of brake pads and new set of wheel bearings. bearings are good but have extra set
I bought the machine new in 03 and I am the only owner. It has a Illinois title that i have in hand. Machine has been xc raced a handfull of times but mainly just a weekend toy. Very well maintained with new or in like new bearings all around.I do have a new complete set of wheel bearings and a new set of swingarm bearings i will throw in . ALOT of work done to it do to the fact that alot of my buddys xc race. Dont really want to get rid of quad but never have time to ride and just takes up room in garage.
CALL 618-292-0008
CAN EMAIL MORE PICS OF WHATEVER YOU WANT TO SEE
$3500 OBO SERIOUS OFFERS ONLY
Engine -
-stage 3 cams both intake and exhaust from lrd(web cam)
-weisco high compression piston(runs good on 93 octane but runs better on 110 and adds more snap thru the gears)
-full lrd exhuast system
-stock carb (but also have a 41mm edelbrock if interested)
-twin air filter
-new transmission in 06
-machine leaks a slight amount of antifreeze from bottom of water pump but could ride all weekend and never have to add any
-machine also leaks slight amount of oil from were the reverse cable goes into the side case. ive been told that it was a common problem and i personally have had it fixed 3 times it is about a 2 dollar gasket that goes bad.
Quad-
ac bumper
ITP C series wheels with itp holehots in front 23x7x10
stock wheels in rear with 20inch razers
*** i have hipers all around with razer 2 in front and razer backs( sold seperate if wanted)
ac front bumper
quad tech hood
prm grab bar
IMS foot pegs
dura blue adj. axle
good sprockets front and rear but may need new front due to the fact it was set up for 22's in rear
D I Dchain in great shape
maier plastic all around in great shape no cracks
full baja belly skid with side motor kick ups
prm swing arm skid
2005 frame that has been gusseted very well and powder coated(my job is a union welder and made gussets myself and went over all welds on frame)
steel braided brake lines all around
billet bar clamp
lonestar tie rods
magura hyd clutch(with steel braided line)
gripper seat cover with added fome for more comfort
roll design stem
bebe handle bars
works triple rate in front rebuilt and valved by derisi racing
ims oversized tank
1000 higher rev box
denton plus one swingarm with round style carrier
twin row carrier
elka dual rate with remote res. and elka linkage
has new sub frame but needs to be touched up with paint
wave rotors all around
twin air air filter with k&n stainless clamp(also have a like new extra air filter)
BRAND NEW maxxstart battery never had a ride on it
clutchs have less than 8 hours on them
I also have a few new sets of brake pads and new set of wheel bearings. bearings are good but have extra set