flyin#5
02-02-2009, 08:20 PM
Parting out the blasty. Was very nice back in the day, now i just have to many quads to keep this one up as much as i used to. This thing rips and is extremly reliable. I had my little cousin on it last time out... for fun i hopped on it and i didnt get off it the rest of the day! pulls just like my 250r except with better bottom end!
Motor Specs: Rechambered head, base spacer setup (decked cylinder), porting (piston ports matched), wiseco forged piston, hot rod connecting rod. Newer clutch plates and basket. Bottom end gone through a year ago aswell as a new top end and does not have much ride time on it since then.
Last rebuild was after 2 years of running strong in races and dunes, never blew up only lost compression due to the rings simply wearing to the exact size of the piston... goes to show this thing runs amazing.
Willing to seperate top and bottom end if need be. Also have another ported cylinder and a rechambered head for sale along with tons of engine parts!
Make offers on the engine
ASR +3 +1 A-Arms in great shape- $300 Shipped
G-Force Axle in decent shape (chrome is always bad on those things)- $125 shipped
Keihin 30mm (bored to 32mm) Flat Slide Carb in good condition- $90Shipped
PB Airbox with rewelded tabs and uni filter- $100 Shipped
FMF pipe and shorty silencer- $150 Shipped
***MAKE OFFERS***
Banshee rear brake setup ready to bolt on a blaster. Needs brake line and to be gone through (been sitting open for a
while). Will send with stock brake line from my yfz.
Front Plastic
Tank
2.5" Extended stock stem
Stock stem polished looks like chrome
2 sets of spindals
2 sets of front hubs
1 set of rear hubs
MX Kenda Klaws all around on .190 douglas tires 85% at least
2 brake discs
2 sprocket hubs/ sprockets
1 swingarm (been welded)
2 carriers
2 sets of stock a-arms in great shape
ANYTHING ELSE YOU NEED ASK I HAVE TONS OF STOCK PARTS
http://img.photobucket.com/albums/v643/Flyin5/P1010150.jpg
http://img.photobucket.com/albums/v643/Flyin5/P1010148-1.jpg
http://img.photobucket.com/albums/v643/Flyin5/P1010148-1.jpg
http://img.photobucket.com/albums/v643/Flyin5/P1010091-1.jpg
Motor Specs: Rechambered head, base spacer setup (decked cylinder), porting (piston ports matched), wiseco forged piston, hot rod connecting rod. Newer clutch plates and basket. Bottom end gone through a year ago aswell as a new top end and does not have much ride time on it since then.
Last rebuild was after 2 years of running strong in races and dunes, never blew up only lost compression due to the rings simply wearing to the exact size of the piston... goes to show this thing runs amazing.
Willing to seperate top and bottom end if need be. Also have another ported cylinder and a rechambered head for sale along with tons of engine parts!
Make offers on the engine
ASR +3 +1 A-Arms in great shape- $300 Shipped
G-Force Axle in decent shape (chrome is always bad on those things)- $125 shipped
Keihin 30mm (bored to 32mm) Flat Slide Carb in good condition- $90Shipped
PB Airbox with rewelded tabs and uni filter- $100 Shipped
FMF pipe and shorty silencer- $150 Shipped
***MAKE OFFERS***
Banshee rear brake setup ready to bolt on a blaster. Needs brake line and to be gone through (been sitting open for a
while). Will send with stock brake line from my yfz.
Front Plastic
Tank
2.5" Extended stock stem
Stock stem polished looks like chrome
2 sets of spindals
2 sets of front hubs
1 set of rear hubs
MX Kenda Klaws all around on .190 douglas tires 85% at least
2 brake discs
2 sprocket hubs/ sprockets
1 swingarm (been welded)
2 carriers
2 sets of stock a-arms in great shape
ANYTHING ELSE YOU NEED ASK I HAVE TONS OF STOCK PARTS
http://img.photobucket.com/albums/v643/Flyin5/P1010150.jpg
http://img.photobucket.com/albums/v643/Flyin5/P1010148-1.jpg
http://img.photobucket.com/albums/v643/Flyin5/P1010148-1.jpg
http://img.photobucket.com/albums/v643/Flyin5/P1010091-1.jpg