pics of maier race cut plastic

[Gray33]

hey i am about ready to buy black race cut plastic front and rear nad attack graphics a total of 430 bucks off of rockymountain and i ma wondering if someone could put up some pics of there maier race cut plastic . Possibly on a yfz 450 lol...

[Gray33]

bump

[416exfreak]

Cut your fenders and pressure wash the balance stickers off of them?

Its alot cheaper, and it will still look good after you ride it a few times, which cant be said for black plastics...:chinese:

[Gray33]

black plastic is sweet

[416exfreak]

Originally posted by Gray33
black plastic is sweet

for 15 minutes.

After you stir up some dust, and get it scratched its gonna look like arse...

but, to each thier own. Good luck gray.:ermm:

[Gray33]

i am debating black or yellow plastic lol what you think?

black-with black a arms black everything

yellow-blue wouldnt have to buy a arms black evel rything else

[ZeroLogic]

Don't ever ever ever get black plastic. You look at it worng and it will be all scatched up.

I'd go with yellow plastic, blue frame a arms ect ect.

[416exfreak]

Originally posted by ZeroLogic
Don't ever ever ever get black plastic. You look at it wrong and it will be all scatched up.

I'd go with yellow plastic, blue frame a arms ect ect.

I agree 100%.

White fronts and yellow rears with some kind of grpahics kit to tie it together would look effin bad....:macho

[Gray33]

and get blue and white number plates, blue or yellow hand gaurds, elka shocks, black a arms,black ims roll design bumper,rear grab bar. blue hmf pipe


a blue frame cost to much and i wouldnt know how to put my quad back together

[416exfreak]

Originally posted by Gray33
and get blue and white number plates, blue or yellow hand gaurds, elka shocks, black a arms,black ims roll design bumper,rear grab bar. blue hmf pipe


a blue frame cost to much and i wouldnt know how to put my quad back together

Correct me if im wrong, but you could probably get the whole frame, subframe, stem, and swinger PC'd for less than $500...

If your planning on elkas, then the PC shouldnt be that hard to acquire.

[Gray33]

Originally posted by 416exfreak
Correct me if im wrong, but you could probably get the whole frame, subframe, stem, and swinger PC'd for less than $500...

If your planning on elkas, then the PC shouldnt be that hard to acquire.

used elkas which are like 500-600 and it would cost me alot of money to paysomeone to put it in a blue frame. where would i take them parts to get pc?

[416exfreak]

Originally posted by Gray33
used elkas which are like 500-600 and it would cost me alot of money to paysomeone to put it in a blue frame. where would i take them parts to get pc?

First a sandblaster, then a powder coating place...

Your local town should have one, if not then a bigger nearby city would.

[Gray33]

how long does ti take to tear everything apart i would probly have to pay someone to tear it apart for me and put it back together

[ZeroLogic]

Talk to Pappy about PC. Hes the man at it. Its not hard to take a quad apart and throw it back together. Get a shop manual and wirte down notes.

[Gray33]

pappy is to far from me lol...and does anyone have pics of maier plastics?

[justin1022]

just spray bomb it and clear coat it about 10 times should hold up well.

[ZeroLogic]

Originally posted by Gray33
pappy is to far from me lol...and does anyone have pics of maier plastics?
UPS or Fed Ex it bro. Tearing a quad apart isn't all that hard. If you can tie your shoe then you should be able to do it.

I didn't think I would be able to put it back together but there's really only one way to learn. I did what my dad told me to. Get a box of Ziploc Baggies to start. For every different part put the bolts to that part in the baggie and label it. Example- one baggie would be Right headlight, another would be Left headlight, etc. etc. It works really well.

[mxpimp2000]

Originally posted by Nova
I didn't think I would be able to put it back together but there's really only one way to learn. I did what my dad told me to. Get a box of Ziploc Baggies to start. For every different part put the bolts to that part in the baggie and label it. Example- one baggie would be Right headlight, another would be Left headlight, etc. etc. It works really well.

good idea thats what i planned on doing if i decide to pc my frame etc. but if u have more of an idea what bolts go where u could just label the baggies plastic,engine,front end,steering,etc.etc.etc but yeh u'll learn its easy

[mittman]

heres mine (brand new) take note no mods(execpt renthal) so this pic was about year and half ago i wish i didnt do black if you just wash it then it doesent look too bad but if you wax it then you will see every little scratch

[Gray33]

Thanks for posting a pic

One question i have for you is ..

How well is the quality of the plastic from maier

[mxpimp2000]

maier is good quality atleast it was for me when i bout it for a 300ex was shiny durable and good fit u just have to drill the holes your self for some mounting

[XCRacer236]

NEVER buy BLACK plastic and NEVER buy Elkas! ;]

[mittman]

Originally posted by Gray33
Thanks for posting a pic

One question i have for you is ..

How well is the quality of the plastic from maier

my maier plastice is a year and a half old and has held up very well. but i wouldnt do black again. the only problems i had with it was getting my headlight in but othere than that it was good

[hypersnyper6947]

Here is a pic of mine....

[hypersnyper6947]

another

[hypersnyper6947]

Last one, now u can see all angles