Brauap
08-22-2008, 02:21 PM
I have the following parts: (shipping not included)
-Stock Snorkle-$5
-Stock Throttle Cable-$5
-K&N-$20
-AC Racing Nerfs-$60
-White Brother's E-Series Custom Shorty-$40
Descriptions:
-OK COND.
-OK COND.
-NICE COND.
-Overall OK COND. --Dent on the right side. Not noticible unless you are standing above them and are looking down.
-Overall OK COND. --This is a custom shorty I made. Comes with: 12 disks, 1 spark arrestor, mounting hardware. When you reseive this, you should add a new washers to the bolt @ the top of the exhaust, because if oyu tend to bottom out exhaust, it will dent it. There is already a small dent to the rear. In the following pictures, if you look at the dent that comes on the exhaust, look a little higher and you will see where it hit the rear caliper. That back is also welded to STOP that annoying, common problem where the E-SERIES brakes off the mid pipe! Washers est. cost=80 cents-- This is a nice exhaust, and will deffently turn heads!
Pictures:
-NO PICTURE
-http://i197.photobucket.com/albums/aa283/braaup/100_1861.jpg
-NO PICTURE
-http://i197.photobucket.com/albums/aa283/braaup/ColtonsPics015.jpg
-http://i197.photobucket.com/albums/aa283/braaup/100_1934.jpg(dirty)
http://i197.photobucket.com/albums/aa283/braaup/100_1935.jpg(dirty)
http://i197.photobucket.com/albums/aa283/braaup/100_1933.jpg
http://i197.photobucket.com/albums/aa283/braaup/ColtonsPics016.jpg
http://i197.photobucket.com/albums/aa283/braaup/ColtonsPics017.jpg(you can see the small dent in this picture. It shinier. The larger indent White Brothers had put on.)
http://i197.photobucket.com/albums/aa283/braaup/ColtonsPics019.jpg(just to give you can idea on the size of the exhaust)
-Stock Snorkle-$5
-Stock Throttle Cable-$5
-K&N-$20
-AC Racing Nerfs-$60
-White Brother's E-Series Custom Shorty-$40
Descriptions:
-OK COND.
-OK COND.
-NICE COND.
-Overall OK COND. --Dent on the right side. Not noticible unless you are standing above them and are looking down.
-Overall OK COND. --This is a custom shorty I made. Comes with: 12 disks, 1 spark arrestor, mounting hardware. When you reseive this, you should add a new washers to the bolt @ the top of the exhaust, because if oyu tend to bottom out exhaust, it will dent it. There is already a small dent to the rear. In the following pictures, if you look at the dent that comes on the exhaust, look a little higher and you will see where it hit the rear caliper. That back is also welded to STOP that annoying, common problem where the E-SERIES brakes off the mid pipe! Washers est. cost=80 cents-- This is a nice exhaust, and will deffently turn heads!
Pictures:
-NO PICTURE
-http://i197.photobucket.com/albums/aa283/braaup/100_1861.jpg
-NO PICTURE
-http://i197.photobucket.com/albums/aa283/braaup/ColtonsPics015.jpg
-http://i197.photobucket.com/albums/aa283/braaup/100_1934.jpg(dirty)
http://i197.photobucket.com/albums/aa283/braaup/100_1935.jpg(dirty)
http://i197.photobucket.com/albums/aa283/braaup/100_1933.jpg
http://i197.photobucket.com/albums/aa283/braaup/ColtonsPics016.jpg
http://i197.photobucket.com/albums/aa283/braaup/ColtonsPics017.jpg(you can see the small dent in this picture. It shinier. The larger indent White Brothers had put on.)
http://i197.photobucket.com/albums/aa283/braaup/ColtonsPics019.jpg(just to give you can idea on the size of the exhaust)