mineralgrey01gt
08-02-2008, 10:45 AM
Ok well as some of you may know, I broke the frame on my trx250r and decided it would be better if I parted it out so here it goes:
85atc engine (recently rebuilt, runs great and shifts just as good, small leak from where the kicker is but I think its just the seal is bad, nothing major, not even 15 hours on fresh rebuild, also the case saver bolt broke, no cracks in the case, no leaks at all, NEEDS A DIFFERENT DRAIN BOLT ON WATERPUMP, RAD VALVE IS NOT BEING SOLD WITH ENGINE) $450+shipping
NIB: Wiseco flat-top piston, 67.45mm in size. It came from Trinity racing off of ebay and I never used it, its only been out the box to make sure everything was with the piston that was suppose to be and it is. The part # is 9345P6745. Im looking to get $50 shipped for it and thats less than what I paid for it.
Boyesen RAD valve $125
88-89 Laeger +1 swingarm $225
Stage IV pipe $110
LRD silencer (good shape) $50
http://img2.putfile.com/thumb/3/7100384074.jpg (http://www.putfile.com/pic/7810076)
Lonestar anti-fade nut w/ rotor $110
Lonestar +4 axle (needs to be rechromed) $165 + shipping
Lonestar twin row bearing carrier $120
Laeger steering stem with houser anti-vibe bar clamps (just found a slight bend in the stem) $140 shipped using UPS
Lonestar steering stem to chassis clamp $30
Tag T2 1 1/8 bars $45
ITP front wheels with holeshot mxr6 19x6x10 tires (10% tread) $90 PENDING
ITP baja front wheels 4:1 offset (thats what offset it looks like) $140
ITP T9 wheels with turf tamers (one has a plug, other is good but loses a little air, one wheel has a slight bend in it, not bad and does not leak air) $80 PENDING
86-87 grab bar (I actually have 2 of these, one is not an A/C grab bar, its just a normal grab bar, the A/C grab bar needs to be bent back into place)$20 each
aluminum radiator shrouds $40
Polished billet oil cap $10
NAC'S Racing silver graphics kit w/ seat cover $120
NAC'S Racing waterpump cover $25
NAC'S Racing stator cover (chrome) $65
NAC'S Racing shock covers $45
Tusk billet aluminum red gas cap (did not fit my 86-87 but is for 250r) $35
IMS shifter $25
Pro Armor kill switch (bought it used and never used it) $15
Maier silver gas tank cover (with big nuts warning sticker, great shape) $30
1986 plastics (local pick up only, not in best shape, just looking to get what i paid) $50
Stock 86 hood and stock 88 or 89 white hood (white hood has been patched) $20
2 sets of stock a-arms (some good some arent) $100
Stock length tie rods with fairly new tie rod ends $45
Stock front shocks w/ black covers $100
Stock overflow tank w/ lid (never used just mounted) $40
Stock 86-87 seat (no brackets) $50
Stock 86-87 red seat cover (never mounted) $30
Stock rear fender brace $20
Stock radiator (no leaks works perfectly) $50
Stock rear brake stay $20
Stock front calipers (both need to be rebuilt) $35
Stock brake pedal (good shape, painted black) $20
Stock rear master cylinder (worked last time used) $30
Stock rear hubs $40
86-87 front spindles with hubs (new bearings and good powdercoat) $80
Rear hubs (excellent splines) $40
Oversized (TOLD IT WAS A LAEGER'S MOUNT) headstay mount $40
Steering stem bushing $10
Billet brake line holders $10
Stock shock linkage from frame to dogbone/lowering link $20
Stock brake hub $10
http://img2.putfile.com/thumb/9/24516133338.jpg (http://www.putfile.com/pic/6496411)
MISC
Nitrous kit for any vehicle (comes with fuel and nitrous solenoids, WOT switch, all lines and a 10lb bottle, also just got fuel rail adapter for any 99-04 4.6L engine) $125
Kicker Comp CVR 12" in box built for sub (one bad voice coil but other works great, aluminum cone version) $50
1983 Honda Odyssey FL250. Runs good but doesnt run right now, needs a new firing coil, needs some TLC was a blast to ride but gotten out of it (LOCAL PICK UP ONLY) $250
http://img1.putfile.com/thumb/4/1092105479.jpg (http://www.putfile.com/pic/5272197)
http://img1.putfile.com/thumb/4/10921054848.jpg (http://www.putfile.com/pic/5272198)
http://img1.putfile.com/thumb/4/10921054855.jpg (http://www.putfile.com/pic/5272199)
http://img1.putfile.com/thumb/4/10921055092.jpg (http://www.putfile.com/pic/5272202)
If you have any questions please ask and ill answer them to the best of my nature.
Here is my email address: lilzilla2008@yahoo.com
EDIT: here is a few pics of it before I redid the plastics black:
http://img2.putfile.com/thumb/6/15322122149.jpg (http://www.putfile.com/pic/8250371)
http://img2.putfile.com/thumb/6/15322122213.jpg (http://www.putfile.com/pic/8250372)
http://img2.putfile.com/thumb/6/15322122281.jpg (http://www.putfile.com/pic/8250374)
http://img2.putfile.com/thumb/6/15322122240.jpg (http://www.putfile.com/pic/8250373)
EDIT: I HAVE PICS BUT SOMETHING IS WRONG AND I CANNOT HOST THEM BUT I WILL SEND THEM TO YOU THROUGH EMAIL, JUST PM ME YOUR EMAIL ADDRESS AND ILL SEND THEM, THANKS!!!
85atc engine (recently rebuilt, runs great and shifts just as good, small leak from where the kicker is but I think its just the seal is bad, nothing major, not even 15 hours on fresh rebuild, also the case saver bolt broke, no cracks in the case, no leaks at all, NEEDS A DIFFERENT DRAIN BOLT ON WATERPUMP, RAD VALVE IS NOT BEING SOLD WITH ENGINE) $450+shipping
NIB: Wiseco flat-top piston, 67.45mm in size. It came from Trinity racing off of ebay and I never used it, its only been out the box to make sure everything was with the piston that was suppose to be and it is. The part # is 9345P6745. Im looking to get $50 shipped for it and thats less than what I paid for it.
Boyesen RAD valve $125
88-89 Laeger +1 swingarm $225
Stage IV pipe $110
LRD silencer (good shape) $50
http://img2.putfile.com/thumb/3/7100384074.jpg (http://www.putfile.com/pic/7810076)
Lonestar anti-fade nut w/ rotor $110
Lonestar +4 axle (needs to be rechromed) $165 + shipping
Lonestar twin row bearing carrier $120
Laeger steering stem with houser anti-vibe bar clamps (just found a slight bend in the stem) $140 shipped using UPS
Lonestar steering stem to chassis clamp $30
Tag T2 1 1/8 bars $45
ITP front wheels with holeshot mxr6 19x6x10 tires (10% tread) $90 PENDING
ITP baja front wheels 4:1 offset (thats what offset it looks like) $140
ITP T9 wheels with turf tamers (one has a plug, other is good but loses a little air, one wheel has a slight bend in it, not bad and does not leak air) $80 PENDING
86-87 grab bar (I actually have 2 of these, one is not an A/C grab bar, its just a normal grab bar, the A/C grab bar needs to be bent back into place)$20 each
aluminum radiator shrouds $40
Polished billet oil cap $10
NAC'S Racing silver graphics kit w/ seat cover $120
NAC'S Racing waterpump cover $25
NAC'S Racing stator cover (chrome) $65
NAC'S Racing shock covers $45
Tusk billet aluminum red gas cap (did not fit my 86-87 but is for 250r) $35
IMS shifter $25
Pro Armor kill switch (bought it used and never used it) $15
Maier silver gas tank cover (with big nuts warning sticker, great shape) $30
1986 plastics (local pick up only, not in best shape, just looking to get what i paid) $50
Stock 86 hood and stock 88 or 89 white hood (white hood has been patched) $20
2 sets of stock a-arms (some good some arent) $100
Stock length tie rods with fairly new tie rod ends $45
Stock front shocks w/ black covers $100
Stock overflow tank w/ lid (never used just mounted) $40
Stock 86-87 seat (no brackets) $50
Stock 86-87 red seat cover (never mounted) $30
Stock rear fender brace $20
Stock radiator (no leaks works perfectly) $50
Stock rear brake stay $20
Stock front calipers (both need to be rebuilt) $35
Stock brake pedal (good shape, painted black) $20
Stock rear master cylinder (worked last time used) $30
Stock rear hubs $40
86-87 front spindles with hubs (new bearings and good powdercoat) $80
Rear hubs (excellent splines) $40
Oversized (TOLD IT WAS A LAEGER'S MOUNT) headstay mount $40
Steering stem bushing $10
Billet brake line holders $10
Stock shock linkage from frame to dogbone/lowering link $20
Stock brake hub $10
http://img2.putfile.com/thumb/9/24516133338.jpg (http://www.putfile.com/pic/6496411)
MISC
Nitrous kit for any vehicle (comes with fuel and nitrous solenoids, WOT switch, all lines and a 10lb bottle, also just got fuel rail adapter for any 99-04 4.6L engine) $125
Kicker Comp CVR 12" in box built for sub (one bad voice coil but other works great, aluminum cone version) $50
1983 Honda Odyssey FL250. Runs good but doesnt run right now, needs a new firing coil, needs some TLC was a blast to ride but gotten out of it (LOCAL PICK UP ONLY) $250
http://img1.putfile.com/thumb/4/1092105479.jpg (http://www.putfile.com/pic/5272197)
http://img1.putfile.com/thumb/4/10921054848.jpg (http://www.putfile.com/pic/5272198)
http://img1.putfile.com/thumb/4/10921054855.jpg (http://www.putfile.com/pic/5272199)
http://img1.putfile.com/thumb/4/10921055092.jpg (http://www.putfile.com/pic/5272202)
If you have any questions please ask and ill answer them to the best of my nature.
Here is my email address: lilzilla2008@yahoo.com
EDIT: here is a few pics of it before I redid the plastics black:
http://img2.putfile.com/thumb/6/15322122149.jpg (http://www.putfile.com/pic/8250371)
http://img2.putfile.com/thumb/6/15322122213.jpg (http://www.putfile.com/pic/8250372)
http://img2.putfile.com/thumb/6/15322122281.jpg (http://www.putfile.com/pic/8250374)
http://img2.putfile.com/thumb/6/15322122240.jpg (http://www.putfile.com/pic/8250373)
EDIT: I HAVE PICS BUT SOMETHING IS WRONG AND I CANNOT HOST THEM BUT I WILL SEND THEM TO YOU THROUGH EMAIL, JUST PM ME YOUR EMAIL ADDRESS AND ILL SEND THEM, THANKS!!!