JessetheKid
07-06-2008, 07:06 PM
This was Pro-Am rider, and now Factory KTM Adam Clark’s old race bike
2004 450r
Chassis:
Long travel Mototech +2.5 A-arms (JB copy)- w/ brand new heims
06 Pep Long travel fronts w/ clamp on res.
Mototech +1.25 Swingarm W/ JB long travel linkage (JB copy)
06 Pep Long travel rear
RPM Dominator Race Hub Axle
Gibson +1 Steering Stem
CCP Steering stabilizer (brand new)
Hiper 4+1 Frt beadlocks w/ BKT’s
Hiper Single beadlock rears w/ BKT’s
Motor:
TC ported head (has a hairline crack by the vale cover, runs fine, I have a spare stock head to go with it)
Wiseco 13:1 Piston
40mm FCR Carb w/ billet adaptor
HRC cam
Vortex Progamable Ignition
Baldwin wiring harness
K&N Filter
Baldwin Airbox lifter kit
WB Alum Pro and Spare TC exhaust
Fluidine oversized radiator
Fan wired to run constant
TAG Fat bars w/ouary grips
Works connection clutch lever w/ hotstart
Maier silver fill fenders w/ Updog graphics
Quadtech Carbonfiber Scoop hood
Cyra handgaurds
AC Propeg nerfbars
Dg National Bumper
Dg Grabar
I am NOT looking to trade or part this bike out. Do not low ball me I do not HAVE to sell this bike just want to get something new. I am keeping the seat that is on it in the pic’s, I have a spare one. Also it had brand new wheel bearings, heim joints on the a-arms, and a brand new steering stabilizer not pictured. Everything was powdercoated Candy red this winter and has about 6 races on it, as does the motor which included a complete tranny over haul. Bike is located in Avon Ohio
6900
http://i221.photobucket.com/albums/dd189/crazyracer31r/Picture002.jpg
http://i221.photobucket.com/albums/dd189/crazyracer31r/Picture.jpg
http://i221.photobucket.com/albums/dd189/crazyracer31r/picture1.jpg
2004 450r
Chassis:
Long travel Mototech +2.5 A-arms (JB copy)- w/ brand new heims
06 Pep Long travel fronts w/ clamp on res.
Mototech +1.25 Swingarm W/ JB long travel linkage (JB copy)
06 Pep Long travel rear
RPM Dominator Race Hub Axle
Gibson +1 Steering Stem
CCP Steering stabilizer (brand new)
Hiper 4+1 Frt beadlocks w/ BKT’s
Hiper Single beadlock rears w/ BKT’s
Motor:
TC ported head (has a hairline crack by the vale cover, runs fine, I have a spare stock head to go with it)
Wiseco 13:1 Piston
40mm FCR Carb w/ billet adaptor
HRC cam
Vortex Progamable Ignition
Baldwin wiring harness
K&N Filter
Baldwin Airbox lifter kit
WB Alum Pro and Spare TC exhaust
Fluidine oversized radiator
Fan wired to run constant
TAG Fat bars w/ouary grips
Works connection clutch lever w/ hotstart
Maier silver fill fenders w/ Updog graphics
Quadtech Carbonfiber Scoop hood
Cyra handgaurds
AC Propeg nerfbars
Dg National Bumper
Dg Grabar
I am NOT looking to trade or part this bike out. Do not low ball me I do not HAVE to sell this bike just want to get something new. I am keeping the seat that is on it in the pic’s, I have a spare one. Also it had brand new wheel bearings, heim joints on the a-arms, and a brand new steering stabilizer not pictured. Everything was powdercoated Candy red this winter and has about 6 races on it, as does the motor which included a complete tranny over haul. Bike is located in Avon Ohio
6900
http://i221.photobucket.com/albums/dd189/crazyracer31r/Picture002.jpg
http://i221.photobucket.com/albums/dd189/crazyracer31r/Picture.jpg
http://i221.photobucket.com/albums/dd189/crazyracer31r/picture1.jpg