Tubsy
06-16-2008, 02:24 PM
I have a MX ready 89 trx 250r. Everything is aftermarket except the frame which was freshly powdercoated not to long ago.
- Gibson Long Travel A-arms with Fresh Axis Shocks
- Roll Design swing arm with Fresh Rear Axis shock
- LRD 265pv (still over 200psi of compression on motor)
- 38mm Airstryker carb
- Stock frame with white powdercoat (had some small cracks but were welded and reinforced and are very strong now)
- Lonestar Stem/ antivibe
- Black Coated AC nerf bars
- Pro taper bars with stators
- Very clean red Maier plastics
- Lonestar axle +2
- Ti molly 2 Krause racing Sprockets and Chains (14/40)
- Full LRD Chrome pipe
- Dual row bearing carrier
- Wide AC racing grab bar
- Carbon fiber hood and QuadTech seat cover.
- Black ASV levers (unbreakable)
- Power Madd handguards
- HD razor tires front and back
- Front Red label Douglas Rims
- Motion Pro throttle and Clutch cable
- Red label wheel hubs
- Black blingstar front bumper
-- Hindson Clutch basket and clutch
All new bearing and bushings in the A-arms and wheel bearings. Alot of billet parts like shifter,kick start etc. Just put new Boss wheel bearings in. The shocks were just re-done about a couple of months ago and have 5-6 rides on them since then. I also not to long ago re-packed the silencer but probably a couple more rides and is due which i have and could give to you if sold. Everything runs perfect on this 250r and runs awesome out in the pits and the tracks. Looking for $5000 or reasonable offers. I will have pictures available tomorrow. This 250r is very clean and starts up in 1-2 kicks. Oil was changed every 2-3 rides. I also have 3 UNI airfilters to go along with it.
Thanks
http://i32.photobucket.com/albums/d9/tmac17/Picture001.jpg
http://i32.photobucket.com/albums/d9/tmac17/PICT0047.jpg
- Gibson Long Travel A-arms with Fresh Axis Shocks
- Roll Design swing arm with Fresh Rear Axis shock
- LRD 265pv (still over 200psi of compression on motor)
- 38mm Airstryker carb
- Stock frame with white powdercoat (had some small cracks but were welded and reinforced and are very strong now)
- Lonestar Stem/ antivibe
- Black Coated AC nerf bars
- Pro taper bars with stators
- Very clean red Maier plastics
- Lonestar axle +2
- Ti molly 2 Krause racing Sprockets and Chains (14/40)
- Full LRD Chrome pipe
- Dual row bearing carrier
- Wide AC racing grab bar
- Carbon fiber hood and QuadTech seat cover.
- Black ASV levers (unbreakable)
- Power Madd handguards
- HD razor tires front and back
- Front Red label Douglas Rims
- Motion Pro throttle and Clutch cable
- Red label wheel hubs
- Black blingstar front bumper
-- Hindson Clutch basket and clutch
All new bearing and bushings in the A-arms and wheel bearings. Alot of billet parts like shifter,kick start etc. Just put new Boss wheel bearings in. The shocks were just re-done about a couple of months ago and have 5-6 rides on them since then. I also not to long ago re-packed the silencer but probably a couple more rides and is due which i have and could give to you if sold. Everything runs perfect on this 250r and runs awesome out in the pits and the tracks. Looking for $5000 or reasonable offers. I will have pictures available tomorrow. This 250r is very clean and starts up in 1-2 kicks. Oil was changed every 2-3 rides. I also have 3 UNI airfilters to go along with it.
Thanks
http://i32.photobucket.com/albums/d9/tmac17/Picture001.jpg
http://i32.photobucket.com/albums/d9/tmac17/PICT0047.jpg