trx 250r LSR t-pin chassis

[dunatic]

2002 LSR MX Chassis (no link) with original MSO……$1850.00. Frame includes front and upper motor mounts
AC Racing Aluminum Pro Peg Nerfs

LSR DC 3 arms (+2/+1) (uses 16.5” shocks)……$ 350.00

LSR T-Pin spindles (uses 88-89 hubs) with tie rods…..$ 250.00

LSR +1 anti vibe stem (7/8” bars)…..$ 200.00

LSR –1 "no link" swinger (TM Design f&r sliders)…….$450.00


PEP triple rate front shocks - 16.5”……….$325.00

PEP single rate rear shock (no link) 17”…….$300.00

All of the above in package deal…….$3500.00 shipped.

LSR +4 axle with LSR anti-fade and factory hubs and rear rotor…….$200.00

ESR TRX 5 pipe and silencer……….$250.00

ESR 40.5 Mikuni carb, with cable and thumb throttle……$200.00

Orange Full bore plastics. …….$200.00 shipped. Front is race cut and in “good” shape, rear has typical burn hole from rear silencer but is usable. Neither piece is broken.

350cc ESR TRX5 porting PV motor. Built new in 2002 from the ground up. New cases, crank, 89 tranny….everything bought new from HONDA. No clutch, No clutch cover, No stator/flywheel, No Counter Balancer Holder, No Stator cover, No intake or exhaust….long block only…..$1150.00

TRX 250r complete front brake system (master, red lines, calipers)……………..$125.00

OEM factory 88-89 front hubs and rotors……...$125.00

Clarke gas tank (Black), with petcock and brackets and cap……..$125.00

ESR intake reed block with stock intake boot…….$100.00

88-89 TRX 250r seat/pan (with latch) and graves seat cover……….$75.00

Hinson adjustable counter balancer holder………….$75.00

Hinson rear brake lever w/spring……$50.00

OEM Stator with un-lightened flywheel…….$125.00

OEM factory 88-89 wiring harness…….$50.00

OEM Factory 88-89 coil………….$50.00

OEM Factory 88-89 CDI………$50.00

OEM Factory 250r kick starter……...$50.00

AC Racing front bumper………….$50.00

AC Racing rear grab bar…………….$35.00

http://img.villagephotos.com/p/2006-6/1193082/025.JPG

http://img.villagephotos.com/p/2006-6/1193082/026.JPG

http://img.villagephotos.com/p/2006-6/1193082/027.JPG

http://img.villagephotos.com/p/2006-6/1193082/029.JPG

http://img.villagephotos.com/p/2006-6/1193082/030.JPG

http://img.villagephotos.com/p/2006-6/1193082/032.JPG

http://img.villagephotos.com/p/2006-6/1193082/033.JPG

http://img.villagephotos.com/p/2006-6/1193082/034.JPG

http://img.villagephotos.com/p/2006-6/1193082/035.JPG

[dunatic]

ttt

[bushwesl]

Definitely get up some pics...

[brokenbones]

pm

[dunatic]

pm'd ya back

[bushwesl]

I tried to send you a PM but your inbox is full...

[dunatic]

let me clean it out now and send it again in 30 minutes.

[Motofool250r]

send me some pics and prices for this stuff
williambrosam@gmail.com

interested in frame and front suspension

[schiavo250r]

how much for everything.

[dunatic]

just updated the 1st post. Ill put up pics when I get home tonite.

[mineralgrey01gt]

will those a-arms work just fine on a stock 250r chassis?

[dunatic]

Originally posted by mineralgrey01gt
will those a-arms work just fine on a stock 250r chassis?

yes, just fine. But youll have to buy the ball joints from LSR, cause these have hiems that will go with the T-Pin spindles.

[dunatic]

pics have been added.


I want to be completely honest about this frame and parts.

chrome is pitting (what a big surprise from LSR huh ?)

The hiem joints in the front end in my opinion need to be replaced...they are sloppy, but this is typical of a T-Pin front end.

The frame has never been cased or bottomed out EVER.

The frame has no cracks (that I can find or see....and I had help today looking it all over to make sure).

The frame has never been repainted or repaired since new.

I have the original MSO (Manufacturers Statement of Origin), so that you can take it to DMV and get a title for it if you like.

The shocks have no leaks and have not been rebuilt since new in 2002.

This bike has sat for the last 3 years. It was build new in 2002, then MX raced until the LSR bearing carrier took a crap at the dunes in 2005 and it was parked.....sandy and dirty in the garage.

If you are truly interested in the WHOLE bike.....I would make a smoking deal on it. PM me for more details. It broke my heart yesterday stripping it all down.

[norcalduner]

pm sent:D

[schiavo250r]

What is a smoking deal for the whole bike?

[dunatic]

pm me....Im not into a debate here

[mineralgrey01gt]

PM sent about orange plastics. I need them drastically!

[dunatic]

I tried to reply, but your mail box is full


Originally posted by mineralgrey01gt
PM sent about orange plastics. I need them drastically!

[dunatic]

ttt

[mineralgrey01gt]

Originally posted by dunatic
I tried to reply, but your mail box is full

hey man, sorry about that, I cleared them out just now. If you dont mind sending me another PM, thanks!!!

[dunatic]

on its way

[dunatic]

Ill update whats left after this weekend

[dunatic]

they are triple rate ZPS, setup for the 200lb rider MX, running the LSR DC4 +2/+1 arms

[dunatic]

thats it til monday...what do you want to see ?

Im an ebay seller with over 1000 positive feedback. I dont and wont sell junk. look me up if you like "OREGONDUNES"

[dunatic]

no chips at all......ok, maybe a few. this bike did not run outside the NW. We dont have rocky tracks.....DIRT baby

[dunatic]

PEP ZPS shock are way better than any stock shock out there. One, they allow the bike to sit lower, giving you a lower center of gravity and better corner.

[kiesta00]

If you still have the trx-5 pipe, email some pictures of the pipe to keith_hester@w-industries.com. Looks like it has a little rust near the flange where the pipes meet. I'm very interested. Let me know.

[dunatic]

it does have some surface rust there....nothing that is going to effect it's performance or longevity.

[kiesta00]

check your PMs

[dunatic]

up on ebay today

just search for trx 250r lonestar

or

Oregondunes as the seller

auctions start tonite at 6:30pm Pacific Time

[BigBore24]

very interested in seat and bumper. if its not on ebay already let me know. im ready to send money. please send pics to roland8883@yahoo.com if you can.

[rossco864]

Maybe to late, but do you still have the pipe for sale?

Thanks

[dunatic]

I do still have the seat, bumper and pipe.

Im at home playing nurse maid to my wife this week, as she just came home from the hospital. I can get to my shop on monday and snap some pics of all the rest of the stuff that I have left.