checking interest

[garrettagr]

hey guys checking interest for this 86R. i had kind of tested the waters earlier but had no pictures. Let me know what you think, see if there is enough interest to let her go. mods are:

1986 Honda 250R
Engine-whole motor is newly rebuilt, right before new years, and only has one trip to glamis on most of the parts. Total time is about 5 hours not including break in.

New Engine parts-
 ESR 340 Power Valve cylinder with TRX 9 porting
 New OEM Honda crank stroked 3mm
 89 clutch update kit
 Tuck clutch kit with plates and fibers
 200 watt Ricky stator stator
 Ricky stator lightweight flywheel
 2 billet inline coolers
 ESR billet exhaust manifold
 CR intake boot
 V force 3 reeds
Older Engine/Drive parts
 Renthal 520 O-ring chain
 ESR trx5 centermount pipe with billet silencer, mounting kit, and ceramic coated pipe springs
 K&N filter with airbox eliminator kit
 ESR carburetor with billet jet board
 Professionally flushed OEM radiator (motor never got over 170 the whole time at glamis)
 RTC radiator air scoops and louvers(best I have ever used and look great too)
 Roll design shift lever
 ESR case saver
 Cases and tranny-were split and machined by ESR right before new years. All parts were inspected and replaced if need be.
 All gaskets, seals, and a few bearing were replaced at time or rebuild.
 I have the receipt and work order from ESR as well to verify work done to the motor and when it was done

Body

 Ceramic Coated Axle/Hubs
 Ceramic coated Rear sprocket with stock gearing
 Ceramic coated steering stem and clamps
 Ceramic coated front engine mounts
 OEM plastics which have been painted
 White seat cover (only one ride)
 IMS 4 gallon desert tank
 Tusk high ATV bend bars
 ASV Levers (brake and clutch)
 Digital Temp gauge from CRJ performance
 RTC radiator air scoops and Louvers (best I have ever used and look great too)
 New grips
 IMS roll design wide footpegs
 ESR parking brake block off

Suspension

 Yarnell Specialties piggyback coilovers on the front and resivor on the rear. All three have two or three rides on them. They will also re-valve them for your weight for free.
 Rear suspension-lowering link. (brand new and never used)

Misc.

 Powder coated frame and swinger candy blue
 Front arms and all calipers painted a gun metal gray
 400ex wheels and rubber, all in good shape


Misc parts that come with the bike

 2 sets of rear paddles, both mounted in wheels
 one set of front sand tires mounted on wheels
 20+ gallons of race fuel
 1 gallon of Klotz Super techniplate 2-stroke oil
 3 quarts of maxima super M 2-stroke oil
 1 quart of redline lightweight shockproof gear oil for trans
 spare 34mm pj carb with cable and cap
 OEM stator
 OEM fuel tank
 PTR 89 race pipe and silencer
 Aluminum air box
 ESR filter eliminator kit (did not fit and would cost more to ship it back, brand new)
 Dune Flag and mount
 New brake lever as a backup
 New fuel filter
 New master link for the chain
 95% complete 86 clutch update kit minus the thrust bearing (brand new)

[garrettagr]

another

[garrettagr]

having trouble posting all the pictures, will try to get some more up later. Again i am just checking interest, probably to part out i am guessing, let me know guys. thanks

[garrettagr]

another

[CSR400EX]

what are you looking to get for it???

[86 Quad R]

interested! what ya want for it and where are you located?

[trapp350]

I am also very interested depending on your location

[garrettagr]

hey guys im located in california. If you are interested let me know. If i dont get back to you right away it is not because i am rude, i just dont have time to check the site and rely to all of the messages as soon as i would like.

thanks garrett

[86 Quad R]

well that leaves me out. too far away. appreciate ya replying back. :cool:

[CSR400EX]

Originally posted by 86 Quad R
well that leaves me out. too far away. appreciate ya replying back. :cool:
same here, or i would jump on it

[2StrokeGod]

price.

[garrettagr]

4500 obo, is that asking too much you guys think? please let me know

[garrettagr]

guys, if you are interested at all let me know. The price is negotiable and if you want it shipped, i can work with you on that as well.

[garrettagr]

what about parting it out, i am open to that as well. let me know