250R 330 Cylinder

[fastredrider44]

I don't know what brand this 330 jug is. Cool Head. Possibly a couple of bores left, Don't know what size piston it needs, and don't have anyway to measure it. It has a measurement written on it, but don't know if thats what it is or not. Cylinder is the O-ring design and does not utilize a gasket.

Look at the pics and make your own determinations.

I was told that an appropriate price for this cylinder is at the 500 to 550 range.

I will do $525 shipped for this cylinder. Don't inquire about trades unless you have a CR500 link and swingarm. I also would rather not to paypal due to the fee that they take out, but pm me for details or questions.

http://i215.photobucket.com/albums/cc281/fastredrider44/100_3504.jpg

http://i215.photobucket.com/albums/cc281/fastredrider44/100_3503.jpg

http://i215.photobucket.com/albums/cc281/fastredrider44/100_3502.jpg

http://i215.photobucket.com/albums/cc281/fastredrider44/100_3501.jpg

[fastredrider44]

bump

[fulltiltrider]

Its pretty tough to spend that kind of money on a cylinder that you dont have any info for. If it would need to be resleaved that would cost over 300 bucks. Get someone to measure the bore. I am interested, but not without solid info

[Aceman]

Originally posted by fulltiltrider
Its pretty tough to spend that kind of money on a cylinder that you dont have any info for. If it would need to be resleaved that would cost over 300 bucks. Get someone to measure the bore. I am interested, but not without solid info

I agree. The going price for the average cylinder usually includes a fresh bore with a new piston and sometimes gaskets. So that's another
$130 piston
$50 bore
$40 topend gaskets

that the buyer still needs. Your price should be no more than $300 in my opinion without solid build/porting info. I saw a pro-x 310 on here a month ago, fresh bore/new piston that sold for around $250 shipped. But that was a steal.

[fastredrider44]

Ok, I'll run a hone through it to see what all will come out. Then I will take some fresh measurements, (not what whoever wrote on the side) and take some fresh pics to let you guys determine whether or not its going to be ok without getting bored or sleeved. I will do the same with my other cylinder, which does have a piston, and I'll more throughly check them to determine what they need. Check out my other listing for the CT 310 cylinder as well. I'll try to do all this tomorrow or Sat. Then we can discuss price. Those figures were given to me off the 250r forum as base starts.

[fulltiltrider]

any info yet

[fastredrider44]

Weds. night is the fastest I will have info. Bare with me, and I'll get the updated pics and measurements on both cylinders.
Thanks

[fulltiltrider]

If that cylinder has at least 2 bores left and you will do 400 shipped since it needs a piston and possibly a bore, I'll buy it. Just let me know soon. I'm in the hunt right now. I found a 310 with a fresh piston esr 9 porting for 400 without the head. So I think thats a decent deal. I would rather have the 330 though

[fastredrider44]

updated pics after hone a measurements. Measurements are written on the side.

http://i215.photobucket.com/albums/cc281/fastredrider44/100_3532.jpg
http://i215.photobucket.com/albums/cc281/fastredrider44/100_3531.jpg
http://i215.photobucket.com/albums/cc281/fastredrider44/100_3530.jpg
http://i215.photobucket.com/albums/cc281/fastredrider44/100_3529.jpg
http://i215.photobucket.com/albums/cc281/fastredrider44/100_3528.jpg
http://i215.photobucket.com/albums/cc281/fastredrider44/100_3527.jpg

[danhung11]

Originally posted by fulltiltrider
If that cylinder has at least 2 bores left and you will do 400 shipped since it needs a piston and possibly a bore, I'll buy it. Just let me know soon. I'm in the hunt right now. I found a 310 with a fresh piston esr 9 porting for 400 without the head. So I think thats a decent deal. I would rather have the 330 though

I have a ESR Billet Head and New Billet Water Neck if you want that motor to have some bling...

Dan

[fulltiltrider]

Sorry guys, allready scored a brand new unported (how I really wanted it) 310 with head, piston, spacer and gaskets on another forum for 625.

Thanks for the offers though

[fastredrider44]

make offers

[fastredrider44]

offers

[mineralgrey01gt]

would my cases have to be machined to run this?

[bushwesl]

Originally posted by mineralgrey01gt
would my cases have to be machined to run this?

Yes.

[mineralgrey01gt]

thanks, i figured that. Ill stick to the original plan

[fastredrider44]

bump

[1Sick250R]

Still have the cyl.? If so send some full pics.
jmscomm@tmail.com

Anyone know if this jug has some bores left? What size piston would I need?