WTB or WTT for TRX250R Heel Guards....

[danhung11]

I am looking for Heel Guards for my XC Build...

Does anyone know where you can buy them NEW?

Thanks,
Dan

[my88r]

I dont think you can buy them new. :ermm:

[TheNewn]

You're either going to have to custom build them. Or order some for like a 400EX or something and modify them. I have IMS pegs on my 250R now and i'm going to look into both. I'm going to look at 400EX heel guards and take some measurements and see if i can make it fit easily enough.

[deathman53]

you probably could get the oem ones that came on 89's. Maybe heel guards from a 400ex, 450r would work with some modding, also. You will have to do some modding to your frame, if you don't have a 89 frame.

[250r4life]

i have the oem ones from my 89, and would be willing to part with them...

[danhung11]

Originally posted by 250r4life
i have the oem ones from my 89, and would be willing to part with them...

I appreciate it. However, I am looking for some aftermarket ones....

[250Renvy]

Originally posted by 250r4life
i have the oem ones from my 89, and would be willing to part with them...

How much?

---------------------
Dan, unless you have an 89 frame it is unlikely they will be able to mount to anything unless you make a mount on the frame or get the heel guards modified.

I think it could work, but might ruin the finish. I'd order 400ex ones and mod them, then powdercoat them.

That's actually one of the reasons I went with a custom frame - so I could use 450R footpegs and heelguards.
------------------------

Is it true that IMS/Roll no longer make 250R footpegs?

[deathman53]

I wouldn't doubt it. I have 2 sets of those pegs 86/87 and one for 88/89. Its just a shame, that those pegs for 86/87 just bent the peg plates over time and with them being discontinued. That is also the reason why I'm going for custom frames to use 450r pegs and my next 2 will have regular pro-peg tubes, so I can use them. I have bent 5 sets of peg plates for a 86 atc250r and one for a 86 atc200x using those pegs. I forget, also a set of peg plates for 86/87 trx250r.

[Rip_Tear]

If you haven't gotten nerf bars yet and plan to you could just get a set with the heel guards from Pro Armor or something?

I am assuming that Pro Armor makes ones for the 250 with Heel Guards like the 400ex ones?

[danhung11]

Originally posted by Rip_Tear
If you haven't gotten nerf bars yet and plan to you could just get a set with the heel guards from Pro Armor or something?

I am assuming that Pro Armor makes ones for the 250 with Heel Guards like the 400ex ones?

It is for an XC Build... do not plan to run nerfs...

[Pro1200]

try calling IMS for their heel guards that go with their footpegs...

[robyone]

IMS doesn't make them any more....this is your best bet :devil:

http://www.exriders.com/vbb/showthread.php?s=&threadid=327394

Have non kick up IMS pegs also if need be.

[danhung11]

Originally posted by robyone
IMS doesn't make them any more....this is your best bet :devil:

http://www.exriders.com/vbb/showthread.php?s=&threadid=327394

Have non kick up IMS pegs also if need be.

I bought these...they should bolt up to my Pegs then I will take them to my fabricator...:devil:

[gregw338]

There is a set of Ims heel gaurds on Ebay right now. I think they end in about 3 or 4 days. Go to Ebay motors then under atv parts and accessories go to 250r parts. Maybe this will help

[moot106]

I believe you can still get some from lonestar or roll design.. check their websites

[danhung11]

Thanks guys!