KXRida
11-08-2007, 08:07 PM
New cylinder/head off of an 02 rm 125
hotrod rod and crank
VPE replaced the gears in the transmission
VPE- front and rear revalved suspension for roughly a 150ish lb rider
Applied top and bottom anodized red tripple clamps
Procircuit pipe and Doma Silencer
Procircuit/JD ignition
Mikuni flat slide carb
Primary drive Gold chain & sprockets w/ new sprocket bolts (3 rides)
New chain guide (3 rides)
New moose wheel spacers
Protaper 1 7/8 bars
Hinsion full clutch assembly-pressure plate, hub, basket
barnett clutch
AC racing sub frame
Michelin starcross front tire (3 rides)
Kenda millville rear (2 rides)
Moose quick adjust clutch perch and new clutch cable
Power Madd hand gaurds
Smith grips (slight rip on left grip from bike falling off the triangle stand)
wiseco top end with cometic gaskets (20 hours)
02 yellow tank and plastics with motoworld graphics
one industries seat cover (very slight rip in the white part)
03 style side panels w/ preprints
Ready racing filter and a twin air filter
Oil was just changed today with hinson 80w oil
Front brake line and caliper off of an 02 with new fernando (sp?) pads
Filter just cleaned and reoiled with Maxima FTT
Front and rear wheel bearings regreased
New fork seals and fresh oil
I honestly may be forgetting some stuff. I had a full list saved on microsoft word, but we just reformatted our computer, so I don't have anything saved on my computer anymore. The kenda millville is not pictured
I'm located in Altoona, Pa 16602.
I am asking $1550. I am also open to trades. Just pm me on here, hit me up on aim at fasterkx105, or email me at fasterkx105@yahoo.com and I'd be happy to answer any questions that you may have.
http://i191.photobucket.com/albums/z152/Rmrider125/chain8.jpg
http://i191.photobucket.com/albums/z152/Rmrider125/chain7.jpg
http://i191.photobucket.com/albums/z152/Rmrider125/chain5.jpg
http://i191.photobucket.com/albums/z152/Rmrider125/chain3.jpg
http://i191.photobucket.com/albums/z152/Rmrider125/rmsprocket.jpg
hotrod rod and crank
VPE replaced the gears in the transmission
VPE- front and rear revalved suspension for roughly a 150ish lb rider
Applied top and bottom anodized red tripple clamps
Procircuit pipe and Doma Silencer
Procircuit/JD ignition
Mikuni flat slide carb
Primary drive Gold chain & sprockets w/ new sprocket bolts (3 rides)
New chain guide (3 rides)
New moose wheel spacers
Protaper 1 7/8 bars
Hinsion full clutch assembly-pressure plate, hub, basket
barnett clutch
AC racing sub frame
Michelin starcross front tire (3 rides)
Kenda millville rear (2 rides)
Moose quick adjust clutch perch and new clutch cable
Power Madd hand gaurds
Smith grips (slight rip on left grip from bike falling off the triangle stand)
wiseco top end with cometic gaskets (20 hours)
02 yellow tank and plastics with motoworld graphics
one industries seat cover (very slight rip in the white part)
03 style side panels w/ preprints
Ready racing filter and a twin air filter
Oil was just changed today with hinson 80w oil
Front brake line and caliper off of an 02 with new fernando (sp?) pads
Filter just cleaned and reoiled with Maxima FTT
Front and rear wheel bearings regreased
New fork seals and fresh oil
I honestly may be forgetting some stuff. I had a full list saved on microsoft word, but we just reformatted our computer, so I don't have anything saved on my computer anymore. The kenda millville is not pictured
I'm located in Altoona, Pa 16602.
I am asking $1550. I am also open to trades. Just pm me on here, hit me up on aim at fasterkx105, or email me at fasterkx105@yahoo.com and I'd be happy to answer any questions that you may have.
http://i191.photobucket.com/albums/z152/Rmrider125/chain8.jpg
http://i191.photobucket.com/albums/z152/Rmrider125/chain7.jpg
http://i191.photobucket.com/albums/z152/Rmrider125/chain5.jpg
http://i191.photobucket.com/albums/z152/Rmrider125/chain3.jpg
http://i191.photobucket.com/albums/z152/Rmrider125/rmsprocket.jpg