REDRON
09-23-2007, 07:08 PM
http://i9.photobucket.com/albums/a75/shootgun/DSCF0164.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0156.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0157.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0158.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0159.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0160.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0161.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0162.jpg
Here is a few parts left over from my 2005 trx450r part out .All reasonable offers will not be refused .This all must go .I can ship most of this stuff priority mail for around 7 bucks .As long as it doesent get over a pund or so .
Polished front stock bumper .I bought this used i dont know wich year it came off of .It does have a few normal scratches but has been buffed out like chrome
There are several race numbers 8 inch white there are two # 2's and two # 3's
6 inch white numbers there is one #2 ,one # 3 and 1 # 1
6 inch black one # 2 and one # 3
Radiator overflow bottle
under tank protector
hot start cable
trail tech flywheel puller
slightly used 40 tooth rear sprocket (just made a few passes down drag strip)
slightly used 38 tooth rear sprocket (just made a few passes down drag strip)
rear carrier circlip
temp light
front fender braces
one slightly used right and left set of tie rod ends (oem honda)
polished dog bone linkage (bearings and spacers good)
capacitor
lower chain roller
over bore racing emergency brake blockoff (billet)
stock skid plate
rear master cylinder metal mount protector
radiator fins
stock clutch pack and steels (replaced not burnt )
radiator hoses
electrical system (needs voltage regulator plug ) Perfect if you are racing motocross and donr need the lights or fan ) Everything else works fine bike ran with the system like this for a while just the fan and lights wouldnt work.
two service manuals (these are some copied manuals i bought off of ebay .Some guy took the color one and ran it off and got it bound ) Its all in black in white but does the trick if you are tooo cheap to spend the big bucks on one from service honda )
brass swing arm linkage specialty bolt with the o rings on it
front hub bearings and parts (has the tapered piece and the spacer) these bearings were repaced before they needed it soo they still have life left in them .
used pressure plate .I ran this plate for a while until i repaced alot of clutch parts and i had no problem with it .The plate got out of aliignment and too much tourque was put on the bolts and broke little pieces of the back part of the 3/4 moon shaped parts .I took a dremel and smoothed out the area that brok off and there was plenty left over for the spring to push up against .
http://i9.photobucket.com/albums/a75/shootgun/DSCF0156.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0157.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0158.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0159.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0160.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0161.jpg
http://i9.photobucket.com/albums/a75/shootgun/DSCF0162.jpg
Here is a few parts left over from my 2005 trx450r part out .All reasonable offers will not be refused .This all must go .I can ship most of this stuff priority mail for around 7 bucks .As long as it doesent get over a pund or so .
Polished front stock bumper .I bought this used i dont know wich year it came off of .It does have a few normal scratches but has been buffed out like chrome
There are several race numbers 8 inch white there are two # 2's and two # 3's
6 inch white numbers there is one #2 ,one # 3 and 1 # 1
6 inch black one # 2 and one # 3
Radiator overflow bottle
under tank protector
hot start cable
trail tech flywheel puller
slightly used 40 tooth rear sprocket (just made a few passes down drag strip)
slightly used 38 tooth rear sprocket (just made a few passes down drag strip)
rear carrier circlip
temp light
front fender braces
one slightly used right and left set of tie rod ends (oem honda)
polished dog bone linkage (bearings and spacers good)
capacitor
lower chain roller
over bore racing emergency brake blockoff (billet)
stock skid plate
rear master cylinder metal mount protector
radiator fins
stock clutch pack and steels (replaced not burnt )
radiator hoses
electrical system (needs voltage regulator plug ) Perfect if you are racing motocross and donr need the lights or fan ) Everything else works fine bike ran with the system like this for a while just the fan and lights wouldnt work.
two service manuals (these are some copied manuals i bought off of ebay .Some guy took the color one and ran it off and got it bound ) Its all in black in white but does the trick if you are tooo cheap to spend the big bucks on one from service honda )
brass swing arm linkage specialty bolt with the o rings on it
front hub bearings and parts (has the tapered piece and the spacer) these bearings were repaced before they needed it soo they still have life left in them .
used pressure plate .I ran this plate for a while until i repaced alot of clutch parts and i had no problem with it .The plate got out of aliignment and too much tourque was put on the bolts and broke little pieces of the back part of the 3/4 moon shaped parts .I took a dremel and smoothed out the area that brok off and there was plenty left over for the spring to push up against .