velocityatv
07-08-2007, 09:42 PM
1987 TRX250R
Stock frame, stem, wheel hubs. The rest has been replaced.
Wiseco racer choice (I believe 68mm)
38mm Keihin A/S
LRD adjsutable pipe.
ESR Silencer built to work with LRD
RPM adjustable timing plate
Dyna ignition
New factory coil
Votex reeds
Ported for Mid-range
Burgard +2+1
Elka triple compression adjust fronts
C&D kitted my rear with a dual rate Elka kit
Jansen stock length chrome swinger - welded on skid mounts.
RPM +1 - +4 Dominator Axle with race hub
RPM tapered carrier
RPM anti-fade
Full skid plates
full set of tires for MX and XC
All tires near new other than Hole shot mx4 rear 18" ( about half the life used up )
Have Razor II's on stock rims for XC. New plastic..needs graphic kit and seat cover to be perfect.
Have stock a-arms on currently for XC racing. Love this quad, but I need a house. I've left out a lot of stuff. I keep really good care of this quad. Call me if really interested.
I'll email my cell number so you can ask any and all questions.
I'm ASKING $3,500.00 ..... willing to negotiate!!!!
Want to talk to me .... shoot me an email velocityatv@msn.com
http://i42.photobucket.com/albums/e318/velocityatv/130_3021.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3019.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3023.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3016.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3013.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3020.jpg
Here is a pic from a while back with my cell phone after I put the plastic on and it still had the A-arms on
http://i42.photobucket.com/albums/e318/velocityatv/250r.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3021.jpg
Stock frame, stem, wheel hubs. The rest has been replaced.
Wiseco racer choice (I believe 68mm)
38mm Keihin A/S
LRD adjsutable pipe.
ESR Silencer built to work with LRD
RPM adjustable timing plate
Dyna ignition
New factory coil
Votex reeds
Ported for Mid-range
Burgard +2+1
Elka triple compression adjust fronts
C&D kitted my rear with a dual rate Elka kit
Jansen stock length chrome swinger - welded on skid mounts.
RPM +1 - +4 Dominator Axle with race hub
RPM tapered carrier
RPM anti-fade
Full skid plates
full set of tires for MX and XC
All tires near new other than Hole shot mx4 rear 18" ( about half the life used up )
Have Razor II's on stock rims for XC. New plastic..needs graphic kit and seat cover to be perfect.
Have stock a-arms on currently for XC racing. Love this quad, but I need a house. I've left out a lot of stuff. I keep really good care of this quad. Call me if really interested.
I'll email my cell number so you can ask any and all questions.
I'm ASKING $3,500.00 ..... willing to negotiate!!!!
Want to talk to me .... shoot me an email velocityatv@msn.com
http://i42.photobucket.com/albums/e318/velocityatv/130_3021.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3019.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3023.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3016.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3013.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3020.jpg
Here is a pic from a while back with my cell phone after I put the plastic on and it still had the A-arms on
http://i42.photobucket.com/albums/e318/velocityatv/250r.jpg
http://i42.photobucket.com/albums/e318/velocityatv/130_3021.jpg