PDA

View Full Version : 250r polished cylinder, ESR head, & chrome swingarm


havinnoj
05-01-2007, 06:43 PM
1) Stock 89 cylinder with piston for short rod setup. 3rd bore, 0 hours fresh bore and piston. Dave Moore ported for play/race sand. Runs very strong. Polished exterior (has pitting as it wasn’t smoothly polished under the intake…etc). 1 exhaust flange bolt hole was stripped; it has since been fixed. Front skirt has been ground down, but is still there. Great top end! Does not come with exhaust flange. fits any year 250r w/ or w/o spacer plate (not included). $350

2) ESR billet head w/dome. Polished exterior. Some surface scratches. $125

These are the ONLY parts for sale at the moment! More to come!

http://www.planetsand.com/memberphotos/53410-ss002.jpg
http://www.planetsand.com/memberphotos/53411-ss004.jpg
http://www.planetsand.com/memberphotos/53412-ss006.jpg http://www.planetsand.com/memberphotos/53413-ss008.jpg
http://www.planetsand.com/memberphotos/53414-ss010.jpg
http://www.planetsand.com/memberphotos/53415-ss012.jpg
havinnoj
05-02-2007, 02:39 PM
bump
havinnoj
05-02-2007, 08:23 PM
2 other buyers fell through
havinnoj
05-03-2007, 12:51 PM
bump
havinnoj
05-04-2007, 08:40 AM
bump!
havinnoj
05-17-2007, 07:48 PM
ttt!
86250rrider
05-17-2007, 07:53 PM
what cc dome is in the head?
havinnoj
05-17-2007, 08:01 PM
not sure off the top of my head. I'll get back to you tomorrow.

It was custom cut for this setup, for use on race gas.

You can pick em up from esr for like 30 bucks blank.
86250rrider
05-17-2007, 08:05 PM
i need 110 on my motor.the sound of detonation send chills up my spine!!! let me know thanks!!
havinnoj
05-17-2007, 08:11 PM
this would be fine.

It was cut to run high octane like that. I usually use stuff 112+ since thats usually what's out here.
havinnoj
05-18-2007, 08:20 AM
bump
havinnoj
05-19-2007, 05:19 PM
My builder doesn't cut specific cc's. Rather, he cuts for the rider, cylinder, and gas.

It's cut high octane race gas and in good shape. Let me know if you want it.
havinnoj
05-20-2007, 01:59 PM
ttt:D
havinnoj
05-21-2007, 12:51 AM
bump
havinnoj
05-22-2007, 11:15 AM
bump
havinnoj
05-23-2007, 12:04 PM
I need this gone!
havinnoj
05-25-2007, 09:07 AM
ttt

I just stepped up to a pro-x cylinder and stroker crank

this stuff needs to go!
havinnoj
05-27-2007, 10:43 PM
bump
havinnoj
05-29-2007, 06:02 PM
on top!

needs to go!

this will make someone real happy!
havinnoj
05-30-2007, 05:29 PM
top
havinnoj
06-01-2007, 12:29 AM
ttt
havinnoj
06-04-2007, 11:44 PM
top
havinnoj
06-06-2007, 10:06 AM
this stuff is top notch!

ttt
havinnoj
06-09-2007, 12:21 PM
ttt