where is everyone with 450r

[pats2007450er]

where is everyone puting there key switch when they take there stock handlebars off.what about the neutral and temp light's where is everyone mounting them.plz post pics if you have them.thanks

[ShiftFMX]

My key is under my hood, Left in the "ON" Position, and My temp light is Zip tied into a bracket and is in plain view when I'm standing...

EDIT: Just saw that you have an ER, this probably wouldnt work in your case.

http://i89.photobucket.com/albums/k216/ShiftFMX/DSC02059.jpg

[ShiftFMX]

Could always get one of these from Trail Tech (http://www.trailtech.net/030-H400F.html) if you dont want to mount it in your plastics

http://www.trailtech.net/media/bar_clamps/atv_x-bar_clamps/030-H400F_trx_400ex_w250.jpg

[Ty's400]

I have found a good spot to zip tie it to the frame and still be able to get to it, to turn it on/off.

[Ty's400]

Sorry picture didn't load first time.

[trx450jason]

I just spliced my ignition wires together so they are always on. As for the temp light you can drill a hole slightly smaller than the light anywhere in your plastic and put it there. Mines right above my right front fender.

[ShiftFMX]

Originally posted by trx450jason
I just spliced my ignition wires together so they are always on. As for the temp light you can drill a hole slightly smaller than the light anywhere in your plastic and put it there. Mines right above my right front fender.

He has an ER, his battery will die

[YZ400EX]

I will post a pic tomorrow of a bracket I had and how it was mounted.. it worked perfect and looks good.. much better than zip ties..

[pats2007450er]

thanks everyone

[YZ400EX]

As promised here is the pic of where I mounted my key switch and temp light.. Its a bracket that comes with 300ex fenders from Maier..You may be able to buy the bracket directly from them by itself.. I just mounted it using one of the mounting holes and then drilled out the other mounting hole big enough for the light to fit in..I think it looks good..

http://i100.photobucket.com/albums/m37/yz400ex/ignition1.jpg
http://i100.photobucket.com/albums/m37/yz400ex/ignition2.jpg

[pats2007450er]

bump

[pats2007450er]

any more ideals

[Sjorge450R]

ditch the dummy lights and put the key in the plastic! look in the right fender towards the tank.

[MAD450r]

in the side pannel in front of my tank. I have an 04 and wanted to keep my key and light. My temp light is in my barpad its a bit hard to see

http://www.imagestation.com/picture/sraid225/pb078902e9d1ef2b6257440aa6e2f4a63/ea1ab625.jpg

sorry this one is a cell pic and looks horrid but you can see how I just carved a small bit of the pad out and I slid the light into the pad. It works well like that and I can see it fine.

http://www.imagestation.com/picture/sraid222/pe0387492faa64ebc4f68b760e47145c4/eb3cb83e.jpg

[Flyin-Low]

Originally posted by ShiftFMX
Could always get one of these from Trail Tech (http://www.trailtech.net/030-H400F.html) if you dont want to mount it in your plastics

http://www.trailtech.net/media/bar_clamps/atv_x-bar_clamps/030-H400F_trx_400ex_w250.jpg

As mentioned above, I love this set-up..

[sandshots]

heres mine, i think this is the best place.

[roundsy]

Originally posted by Flyin-Low
As mentioned above, I love this set-up..

how much did you pay for that thing CDN?...and where'd you pick er up?

[Flyin-Low]

I ordered that baby from http://trailtech.net/atv_x-bar_clamps.html

Not too sure what it came to but it is pretty sweet. I over tightened the freaking clamp and cracked the chrome :( I got a trail tech VAPOR with it also and the bars. Nice setup and cleans it all up.

-Martin

[RATHRACING450R]

heres mine, not a close pic, so i circled it in yellow, just zip-tied to the frame, works great and no drilling involved!!!:)