RM 125 for sale $1200 obo

[KXRida]

The Cylinder on the bike needs replated. I thought it was a top end, but the cylinder needs to be replated or bored. The bike runs, but has low compression even with a brand new top end and is hard to start.

VPE-race cylinder/crank/hotrod rod and all the gears in the transmission
VPE- front and rear suspension revalved
VPE-shaved head
Applied- top and bottom tripple tree
Procircuit- pipe and silencer
Procircuit-ignition
Mikuni-flat slide carb
Polished swingarm
Renthal- chain
Protaper oversized bars
Braking rear rotor
Hinsion full clutch assembly-pressure plate, hub, basket
AC-sub frame
new fork seals
new brake pads
Dunlop rear tire > needs a new one
Pirelli-front tire> about 50% left.
New Moose-quick adjust clutch perch and cable
Ceet seat cover
Power Madd-hand gaurds
After market-number plate with mesh inlay
boyesen rad valve w/ new reeds
Scott-grips
Brand new wiseco top end with cometic high comp. gaskets
new oem kill switch

http://i123.photobucket.com/albums/o298/purplepillz712/000_0596.jpg

http://i123.photobucket.com/albums/o298/purplepillz712/000_0599.jpg

http://i123.photobucket.com/albums/o298/purplepillz712/000_0602.jpg

Like I said the bike will sometimes fire, but it gets a lot of blow by. I just had it at the local shop and they cleaned the carb, flushed the cases, rejetted the carb, and did the top end, but the cylinder needs to be replated because it is causing it to loose compression. The bike will start sometimes on a kickstart, but most of the time requires a bump start. I do have the reciept somewhere for the work that was done on it. Besides replating the only thing the bike needs is tires and graphics. The graphics pictured are no longer on the bike. I had the intent of putting new graphics on, but that never happened. I just haven't gotten around to getting new ones on.


I am located in Altoona, Pa buy must pick up or arrange shipping. I am asking $1200 obo. If I had the time to ride it I would get the cylinder replated, but college takes up a lot of time. If you have any questions please feel free to email me at fasterkx105@yahoo.com or IM me at fasterkx105

Thanks.

[ZeroLogic]

What year is it?

[HondaRacer300ex]

2001.

[KXRida]

For $1250 I'll throw in a rear kenda millville with 3 rides on it, renthal sprocket, original number plate, new kill switch, and new levers

Here are some pictures with the back grounds on it, but for $1200obo they are not included.

http://i84.imagethrust.com/i/974029/bad2.jpg

http://i84.imagethrust.com/i/974030/bad3.jpg


Here is what the bike looks like as it sits for sale. (sorry for the bluriness)

http://i84.imagethrust.com/i/974031/bad4.jpg

[ZeroLogic]

How are all of the bearings from the suspension to the motor? Fork Seals? Clutch? Cracks or bends anywhere? All it needs is to be replated?

[KXRida]

It has fresh seals in the motor all done by VPE, fresh top end done by the local shop. Not sure about the linkage bearings, but the guy before me put new wheel bearings in front and rear. The stem bearing is pretty new as well. VPE also put in a hinson clutch basket, pressure plate, clutch hub, and a barnett clutch. The basket has very minimal knotching and the clutch was put in about 3 months ago, but the bike has sat for about 2 months. The left rear side panel has a slight crack in it where the bolt goes through to the seat and the hole on the bottom of the side panel is hollowed out. Other than that and a new tires, it just needs replated. For $1250 I'll throw in a rear kenda millville with 3 rides on it, renthal sprocket, original number plate, new kill switch, and new levers

[ZeroLogic]

Where are you at?

[KXRida]

Altoona, Pa. It has roughly 125psi but that is flirting with the minimum to run, so if you would come down to look at it I doubt it would start. I have the local shop service record here somewhere. The did the top end. Also if you want to get the cylinder replated, one of the best guys to talk to is steve at moto814 porting in Allentown, Pa. He's a great guy who does amazing work at very reasonable prices.

Also, for $1250 I'll throw in the extras a few posts up.


I can also get new pictures if you want.

[ZeroLogic]

I'm very intrested, but I have to talk to my dad about it. Could you get some close ups of the motor on each side, and any other pictures if you could. Could we meet half way, I am located near Milford Pa so its quite the ride for me...

[KXRida]

Yea I can get more pics. Milford is down around wilksbarre right? I'm not sure about driving because I'll be starting my college summer classes early while I'm still in high school so my time will be very limited. That is the main reason why I'm selling it. Around where would be half way?

[ZeroLogic]

My dad decided to go half way with my on a 05 Yz 125 so I can't get this. Sorry. Good luck with the sale. Bump.

[KXRida]

also open to trades. PM me with a reasonable offer and we'll talk.

[KXRida]

Anyone, I'd be willing to pay some cash as well if you have anything to trade.

[KXRida]

Here are a bunch of new pics.

http://i84.imagethrust.com/i/983973/engine.jpg

http://i84.imagethrust.com/i/983974/engine2.jpg

http://i83.imagethrust.com/i/983976/engine4.jpg

http://i83.imagethrust.com/i/983977/front.jpg

http://i84.imagethrust.com/i/983978/frontside.jpg

http://i84.imagethrust.com/i/983979/frontside2.jpg

http://i83.imagethrust.com/i/983980/rear.jpg

http://i84.imagethrust.com/i/983981/rearside.jpg

http://i84.imagethrust.com/i/983982/rm125.jpg

[Exrider434]

trade for 98 300ex? i have more info if you are interested

[KXRida]

sent you a PM

[400exrider989]

just wanted to comment on a nice bike for a good price that can be fixed cheaply and very powerful and reliable ... free bump too

[KXRida]

Trades welcome. I could maybe throw in some cash if needed.

[KXRida]

ttt

[KXRida]

I may be willing to let it go for $1000. Pm me and we'll talk.

[KXRida]

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=200100351073

[KXRida]

the first link is invalid...


http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=200100609855