PDA

View Full Version : Huge Yfz Part Out



660LE
03-22-2007, 04:59 PM
All parts are used but all came from a running quad. Shipping prices are not included. I will also make deals if you buy multiple parts. PLease contact via PM or email andrewmckinnon99@Hotmail.com

CHASSIS

04 frame, with gussets, lsr 6 point subframe mounts. There are a few bolt
holes stripped, the skid plate mounts and 1 front plastic mount hole. The bottom of the frame has tubing welded over it from the original tubing starting to cave in. This happened in 04 and has been perfect ever since. 400$ OBO

05 Linkage pullrod and shock 75$

upper and front motor mounts 25$

swingarm bolt nut and washer 15$

rear hubs 40$

rear pull rod 30$

pitman arm 15$

beat x factor skid 20$

rear master cylinder, stainless line, pedal, and caliper 105$

gibson dual row carrier with brake plate 125$



MOTOR

Complete bottom end. Low hours 05 crank. Hinson clutch basket. Gyt-r kickstart kick with kicker. Starter block off plug. Prodesign case svaer and shifter. Tranny was replaced mid summer. At the same time the crank bearings and tranny bearings were replaced as well. 950$ OPEN TO OFFERS

2 oil tanks and lines, one with a billet dip stick 25$ 30$ for one will billet dipstick

2 stock intakes 10$ each

2 starters 50$ each

oil pump & gears 50$

counter balancer & gears 50$

complete clutch (basket, plates, push rod, ball, pressure plate, inner hub) 125$

timing chain and guide 15$

shift mechanism 45$

clutch cover 20$

stator and cover 75$

stock flywheel 60$

carb with hotstart, ncqv needle, zypty fuel screw 225$

2 front master cylinders one with broken lever other with no lever 40$ each

Full big gun pipe. Cut down 4 inchs. fresh packing. 100$

ebrake setup 10$

black crankcase vent box 10$



MISC

Stock blue race cut plastic 90$

gas tank 40$

air box 10$

2 stock bumpers 5$ each

1 Blingstar flight bumper. Needs new powdercoat 75$

stock shifter 5$

thumb throttle 15$

seat with ripped cover that should be replaced for looks. 30$

rad with no leaks and cap , fins dont look the nicest 25$


http://www.imagestation.com/picture/sraid224/p7e6a88ba22f183db191cafc4ed957ce7/eac287f9.jpg

http://www.imagestation.com/picture/sraid224/p1640d9f55a7aa716e400cd2446a8aa0d/eac2878d.jpg

http://www.imagestation.com/picture/sraid224/p56334c2fcb7606110a5cd2160c11a49a/eac2877b.jpg

http://www.imagestation.com/picture/sraid224/p580a0ae46796e5e3c513a027a262c893/eac28765.jpg

http://www.imagestation.com/picture/sraid224/p3a759a52bcd4f38f5068480da59b98cd/eab64869.jpg

http://www.imagestation.com/picture/sraid224/pcc288dfc775a5b6ec473e88f4ea4701e/ea8f6663.jpg

http://www.imagestation.com/picture/sraid225/pc1ecbe0ab265ea63ec970c5ca2e6ce3d/ea6cf030.jpg

jixxer
03-23-2007, 06:17 AM
Could I get some more pics of the carb to artgregoryiv@hotmail.com

660LE
03-23-2007, 08:06 PM
pics sent :D

jixxer
03-23-2007, 08:15 PM
pm sent