atallblonde724
03-14-2007, 01:18 PM
This quad was built by Kenny Vaughn of KFAB in Texas.
Motor built by Billy Holt in Alabama.
2006 Xtreme Pro Shark
WRHracing 2001 Scrambler motor 108cc
frame gussetted and lightened
KFAB +3 A-arms
KFAB +2 swing-arm
KFAB nerfbars
KFAB Rear foot brake
KFAB rear grab bar
KFAB screened front bumber
KFAB +2 chromed steering stem
long travel FOX Float shoxs
400ex calipers/spindles/brakes
steel braided brake lines
black Pro Taper handlebars/grips
300ex rear carrier
300ex rear brake
+4 rear axle - keyed/adjustable
Douglas rims 8x8 rear 10x5 front
Holeshot MX tires
WRHracing pipe
Keihin 24mm carb
Terry cable throttle
special throttle cable built for the 24mm carb
Pro design kill switch
Full belly skid plate
spare brand new axle - this is a keyed axle not durablue and only costs $100 not the $400 a durablue costs.
The motor:
I have the receipt for the build.
Stroker Motor kit 108cc - $530
port work on cylinder - $400
Ceramic coating on exhaust port - $80
Small race fan - $28
PVL ignition - $450
Aluminum spacers - Spacers for crank/starter motor & oil plug -$22
Ceramic main bearings - $80
Left and right seals - $10
Clutch kit - $65
New top in last month -gaskets/piston & rings - $95
Runs on race gas 50:1
I will take more pics and also going to list on ebay. I will list link as soon as I get it listed.
This quad is ready to go and has only been raced a hand full of times last season. Was trying to decide if my daughter was going to race this year but she is to tall.
$7,000.00
Motor built by Billy Holt in Alabama.
2006 Xtreme Pro Shark
WRHracing 2001 Scrambler motor 108cc
frame gussetted and lightened
KFAB +3 A-arms
KFAB +2 swing-arm
KFAB nerfbars
KFAB Rear foot brake
KFAB rear grab bar
KFAB screened front bumber
KFAB +2 chromed steering stem
long travel FOX Float shoxs
400ex calipers/spindles/brakes
steel braided brake lines
black Pro Taper handlebars/grips
300ex rear carrier
300ex rear brake
+4 rear axle - keyed/adjustable
Douglas rims 8x8 rear 10x5 front
Holeshot MX tires
WRHracing pipe
Keihin 24mm carb
Terry cable throttle
special throttle cable built for the 24mm carb
Pro design kill switch
Full belly skid plate
spare brand new axle - this is a keyed axle not durablue and only costs $100 not the $400 a durablue costs.
The motor:
I have the receipt for the build.
Stroker Motor kit 108cc - $530
port work on cylinder - $400
Ceramic coating on exhaust port - $80
Small race fan - $28
PVL ignition - $450
Aluminum spacers - Spacers for crank/starter motor & oil plug -$22
Ceramic main bearings - $80
Left and right seals - $10
Clutch kit - $65
New top in last month -gaskets/piston & rings - $95
Runs on race gas 50:1
I will take more pics and also going to list on ebay. I will list link as soon as I get it listed.
This quad is ready to go and has only been raced a hand full of times last season. Was trying to decide if my daughter was going to race this year but she is to tall.
$7,000.00