View Full Version : Revised 06' Rossier vs. DASA Pipe Test
Mobile Dyno
12-03-2006, 07:32 PM
Today Chad (DRG), Alex (czrider263), and his dad came down to dyno test his new Web 943 cam. He had the Web 208. We also threw in a Rossier vs. DASA pipe test. This is Rossier's New Redesigned 06' pipe. This is the First test posted of the Revised 06' Rossier. Here are the mods on this 06':
Stock Bore
Stock Stroke
DRG Porting
43mmFCR
Web 943
Oversized Buckets
14:1 Baldwin
Stock Valves
stock box no lid drg filter
Temps for todays testing were 50* & 31% Humidity. Kind of Chilly.
We started with the Rossier and we ended out jetting with a K195 main. Then the DASA was installed and we dialed it with a K185 main.
The crew hard a work...
:huh
Mobile Dyno
12-03-2006, 07:36 PM
Rossier
Mobile Dyno
12-03-2006, 07:38 PM
DASA
Mobile Dyno
12-03-2006, 07:41 PM
Here are the graphs over RPM. Very Close and Very Smooth curves.
Mobile Dyno
12-03-2006, 07:47 PM
A/F.
Red is DASA and a K185 main
Blue is Rossier and a K195 main
ghott
12-03-2006, 08:03 PM
Very sweet.
Looks like Joe has his stuff together on the 2006 RE Pipe!
Both of those jets are HUGE for an 06'. The highest I had seen before this was a 175 main.
I just wish I had an 06' :(.
Good looking tests Matt.
Mobile Dyno
12-03-2006, 08:07 PM
Thanks Ghott:) Yea, Joe is making great power at a great cost. It will only get better:D
ghott
12-03-2006, 08:18 PM
What does he sell the 06' pipes for?
And I've heard he will be coming out with a revised 05' pipe...
Any word on when?
Mobile Dyno
12-03-2006, 08:20 PM
I believe the they are around $450 for a Full system, but call Joe to make sure.
He is coming out with a revised 05' and we will be testing that soon. No word on when.
ghott
12-03-2006, 08:25 PM
Thanks, I'll keep my eyes peeled.
ghott
12-03-2006, 08:31 PM
Another question for you...
Did he mention a reason as to why he went from the 208 to the 943/921?
I'd imagine the 943 is a little easier on the valve train, but it looks like he lost about 1.5-2 horses?
czrider263
12-03-2006, 11:01 PM
Originally posted by ghott
Another question for you...
Did he mention a reason as to why he went from the 208 to the 943/921?
I'd imagine the 943 is a little easier on the valve train, but it looks like he lost about 1.5-2 horses?
NO I made the same peak hp with another 2 all around. but looking at the graphs you will see that is will drop off after 9,500 or so so its a great cam to that i think the loss up top is fine for what you get down low.
Also thanks matt for a fun day of testing.
wppracing
12-04-2006, 06:12 AM
Looks good Alex.....:) Take it to the track and give us a ride report.
Matt,
Do you have any runs with the 208 installed ? Then we could see where the difference is between these 2 cams on his build.
Mobile Dyno
12-04-2006, 06:19 AM
Chad is going to post that graph in a few min. Alex made a great choice on a cam.
chad502ex
12-04-2006, 06:20 AM
the 208 over-camed this build for sure.....
I call the 943 'the 208 mini-me'.
the 943 is almost the same cam with normal base circle and smaller valve lift on the intake.
0.356 intake lift on 943
0.408 intake valve lift on 208
same lobe phasing
same duration
same overlap
same exhaust dur/lift.
essentially, the 943 is a less agressive 208 that is considered 'drop-in' cause the 943 will not wear springs out on 0.356" lift...
Try not to get confused though about a smaller cam, it is possible to make more power on a smaller came if your port is tuned to flow more at 0.356" than 0.408". In other words, sometimes a cam can be too big and will cause power loss when the valve is full out the velocity falls significantly and the intake charge falls out ouf suspension....
chad502ex
12-04-2006, 06:21 AM
and tq..
ghott
12-04-2006, 06:42 AM
Matt,
Do you have graphs of all the dyno runs done with each pipe to try and get an "average" between the two?
Chad,
Good info on the 943. I'm really starting to like the way that cam is looking. Maybe it'll replace my HCS2 sometime down the line :).
chad502ex
12-04-2006, 06:50 AM
Originally posted by ghott
Chad,
Good info on the 943. I'm really starting to like the way that cam is looking. Maybe it'll replace my HCS2 sometime down the line :).
the cam was suppose to be purchased for czrider263 05 450R build, but after looking at czrider263 ol' 06 54hp 208 dyno run using the FCI, it was discussed that the 208 was being a bit lazy so i suggested czrider263 to install it and see if the power was better.
It was..
very impressive, but still this is basically a 208 with the same timing just a little less intake valve lift to help with intake velocity...
wppracing
12-04-2006, 06:50 AM
I am glad told Alex about that cam when I say them at Rausch Creek.
More useable HP and TQ and perfect for the track.
Good comparrison between the 2.
chad502ex
12-04-2006, 06:53 AM
Originally posted by wppracing
More useable HP and TQ and perfect for the track.
we were going to install this in the new 05 build, but i suggested that he compare it to it's big brother on the 06 after Dee and I had great discussions about intake velocities...
The over-rev beyond peak falls off hard though with the 943...
dont even try taking this cam to 11k..
xsr_racing28c
12-04-2006, 06:54 AM
Chad and Alex.. <Looks like that 943 cam is pretty sweet!! I can't wait to see what that 05 of yours puts out.. Or mine for that matter.. :devil:
chad502ex
12-04-2006, 06:56 AM
Originally posted by xsr_racing28c
Chad and Alex.. <Looks like that 943 cam is pretty sweet!! I can't wait to see what that 05 of yours puts out.. Or mine for that matter.. :devil:
Yea, Jay.... alex is gonna take off the head cause there is a little squeezing required to gain up on 3 more... ;)
#404's Dad
12-04-2006, 07:07 AM
Nice results guys.
I also run the 943 and have a 208 in my cam arsenal but I will say on my build that the seat of the pants and drag racing results are just the oposite of whats shown here.
Proving that one cam can react totaly different in two differnet motors and everything needs to be built as a package to perform correctly and it seems this motor like the 943 much more than it does the 208.
Now what about a Dasa systems thats made for this setup? You guys used the shelf system I take it, which would only be fair Shelf vs Shelf but I know Dasa will make a pipe for anyone for their specific build for the same price all you have to do is ask.
Again nice results guys and thanks for sharing with everyone.
Corey
chad502ex
12-04-2006, 07:14 AM
Originally posted by #8trx450r
Nice results guys.
I also run the 943 and have a 208 in my cam arsenal but I will say on my build that the seat of the pants and drag racing results are just the oposite of whats shown here.
Proving that one cam can react totaly different in two differnet motors and everything needs to be built as a package to perform correctly and it seems this motor like the 943 much more than it does the 208.
Now what about a Dasa systems thats made for this setup? You guys used the shelf system I take it, which would only be fair Shelf vs Shelf but I know Dasa will make a pipe for anyone for their specific build for the same price all you have to do is ask.
Again nice results guys and thanks for sharing with everyone.
Corey
Oh sure corey,.. cam shaft selection is not going to be the same on all builds.. there is a big difference between the 06 TRX head (like this one) and the 05 TRX head... the 06 head is all about velocity and the 943 complements that perfectly... still not bad,... it'll get better for sure..
hey corey, the Rossier was not custom just revised
Enjoy Alex.
#404's Dad
12-04-2006, 07:19 AM
Originally posted by chad502ex
Oh sure corey,.. cam shaft selection is not going to be the same on all builds.. there is a big difference between the 06 TRX head (like this one) and the 05 TRX head... the 06 head is all about velocity and the 943 complements that perfectly... still not bad,... it'll get better for sure..
Enjoy Alex.
For sure dude, the 06 and 04 are two totaly different animals in deed.
again, Nice Job
xsr_racing28c
12-04-2006, 07:33 AM
Originally posted by chad502ex
Yea, Jay.... alex is gonna take off the head cause there is a little squeezing required to gain up on 3 more... ;)
Squeeze away!!! Are you going to Dyno after that again?? ~Jay
chad502ex
12-04-2006, 07:44 AM
Originally posted by xsr_racing28c
Squeeze away!!! Are you going to Dyno after that again?? ~Jay
for sure :thumbsup
chad502ex
12-04-2006, 07:47 AM
Originally posted by #8trx450r
For sure dude, the 06 and 04 are two totaly different animals in deed.
again, Nice Job
hey corey,.. i just edited one of my previous post to clarify...
the Rossier is not a custom exhaust... this 06 Rossier is just revised from before.... in other words, this wasn't a custom exhaust as you suggest that DASA could offer just what is offered to public.
#404's Dad
12-04-2006, 07:50 AM
Originally posted by chad502ex
hey corey,.. i just edited one of my previous post to clarify...
the Rossier is not a custom exhaust... this 06 Rossier is just revised from before.... in other words, this wasn't a custom exhaust as you suggest that DASA could offer just what is offered to public.
I knew what you were saying Dawg, I know Joe Joe revised it and is revising the 04-05 too :) was just saying you CAN gte a Dasa tailored to your needs is all.
Corey
chad502ex
12-04-2006, 08:00 AM
Originally posted by #8trx450r
I knew what you were saying Dawg, I know Joe Joe revised it and is revising the 04-05 too :) was just saying you CAN gte a Dasa tailored to your needs is all.
Corey
OK, kewl.. thanks for your input Corey! :thumbsup
ghott
12-04-2006, 08:07 AM
Originally posted by ghott
Matt,
Do you have graphs of all the dyno runs done with each pipe to try and get an "average" between the two?
:devil: :macho
chad502ex
12-04-2006, 08:17 AM
Originally posted by ghott
:devil: :macho
Gary, over 30 runs were consistently what you see here...
almost completely atop each other as one curve...
ghott
12-04-2006, 08:31 AM
Thank you Chadwick ;).
Joe@rossier
12-04-2006, 12:12 PM
Originally posted by #8trx450r
Nice results guys.
I also run the 943 and have a 208 in my cam arsenal but I will say on my build that the seat of the pants and drag racing results are just the oposite of whats shown here.
Proving that one cam can react totaly different in two differnet motors and everything needs to be built as a package to perform correctly and it seems this motor like the 943 much more than it does the 208.
Now what about a Dasa systems thats made for this setup? You guys used the shelf system I take it, which would only be fair Shelf vs Shelf but I know Dasa will make a pipe for anyone for their specific build for the same price all you have to do is ask.
Again nice results guys and thanks for sharing with everyone.
Corey
Just want to let you all know that the 06 TRX pipe has never been changed at all since I released it almost a year ago. To bad it could have been dynoed with 14 discs on the back with a closed end cap ( worth .2-.4 tenths of a HP over totally open end cap on my own personal quad)
chad502ex
12-04-2006, 12:14 PM
:huh
oh WOW!
:macho
Chino886
12-04-2006, 12:29 PM
Originally posted by chad502ex
:huh
oh WOW!
:macho
And those discs are on the way to me.......wooohooo! :macho
xsr_racing28c
12-04-2006, 01:02 PM
:p Guess you dont have to even think about getting a new pipe Dave...
Jay
ghott
12-04-2006, 01:04 PM
Originally posted by xsr_racing28c
:p Guess you dont have to even think about getting a new pipe Dave...
Jay
Remember, this is on a 2006, not a 2004/2005.
Joe isn't coming out with his 04/05' revised pipe until sometime in January.
Chino886
12-04-2006, 01:04 PM
Originally posted by xsr_racing28c
:p Guess you dont have to even think about getting a new pipe Dave...
Jay
Yeah, I am happy! Will be even happier once I get my arms back! :huh
Chino886
12-04-2006, 01:06 PM
Originally posted by ghott
Remember, this is on a 2006, not a 2004/2005.
Joe isn't coming out with his 04/05' revised pipe until sometime in January.
Yup, my R used to be ER! :blah:
chad502ex
12-04-2006, 01:11 PM
Originally posted by ghott
Remember, this is on a 2006, not a 2004/2005.
Joe isn't coming out with his 04/05' revised pipe until sometime in January.
there could be a test before its releash tho.... ;)
xsr_racing28c
12-04-2006, 01:27 PM
i can't wait to see what the revised version of the 04-05 puts out
czrider263
12-04-2006, 01:48 PM
Well i just got off taking the 06 for a ride and all i can say is good GAWD !!!!! This thing is just nasty. I felt a stronger pull all around. most notable coming out of turns and holshots. i don't even what to know what another 3 would be HOLY S%&T
ghott
12-04-2006, 02:12 PM
Originally posted by czrider263
Well i just got off taking the 06 for a ride and all i can say is good GAWD !!!!! This thing is just nasty. I felt a stronger pull all around. most notable coming out of turns and holshots. i don't even what to know what another 3 would be HOLY S%&T
Sounds like the 943 did it for ya :).
Looks like it fairs well in both the 04/05 machines, and the 06/07 machines. I'm really starting to like how this cam looks :).
Chino886
12-06-2006, 11:54 AM
Originally posted by Joe@rossier
Just want to let you all know that the 06 TRX pipe has never been changed at all since I released it almost a year ago. To bad it could have been dynoed with 14 discs on the back with a closed end cap ( worth .2-.4 tenths of a HP over totally open end cap on my own personal quad)
Chino installed 14 discs and the closed endcap last night! Chino did not start it cause Chino is missing A-arms and front shocks! :macho
Chino also noticed that the new TC Racing exhaust uses the same endcap that Chino has as a spare in a box, Chino will check it out! ;)
Chino needs to find a dyno soon and close by! :devil:
Chino likes typing in 3rd person! :blah:
czrider263
12-06-2006, 01:10 PM
Originally posted by Chino886
Chino installed 14 discs and the closed endcap last night! Chino did not start it cause Chino is missing A-arms and front shocks! :macho
Chino also noticed that the new TC Racing exhaust uses the same endcap that Chino has as a spare in a box, Chino will check it out! ;)
Chino needs to find a dyno soon and close by! :devil:
Chino likes typing in 3rd person! :blah:
Hope you like emmmmm:D
Chino886
12-06-2006, 01:13 PM
Originally posted by czrider263
Hope you like emmmmm:D
I don't know, no dyno test yet (butt or dynojet)! :(
Powered by vBulletin® Version 4.2.1 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.