ESR 310R Powervalved motor

[400EX QUADER]

Hey I have a esr 310 powervalve motor that's in my trx250rforsale that runs great. It's an 85' atc motor (I prefer the atc motors for racing). Well let's see... It has the esr 310 powervalve motor as you know, hotrods longrod crank, spacer plate for the longrod crank, hinson clutch, hinson adjustable timing plate, mid-topend dome, etc... Also a esr trx5 centermount pipe, k&n and a pwk 39mm carb. the motor only has about 6 rides on it since ALL of these mods were done. I just took the head off and the piston was a caramelish color. Runs awesome. Beats 450's, banshees, raptors, other 250r's, etc... It's on its original bore. Always run on 110 octane racegas with torco gp-7 premix (the best stuff) at the ratio of 40:1. Actually a tad more than 40:1 since I usually dump a little extra in just to be safe. The topend alone is $1600+ shipping. I also have a never been used midrange dome to go with it. Pm me with your offer BEFORE SHIPPING. I dont know howmuch shipping is. anybody know? Drop this into your 250r or possibly another frame and have a quad that runs like a raped ape. My buddy's always say that my 250r runs better then everybody elses that they see. So yeah pm me, email me at cory400exquader@hotmail.com or message me at cory2fittyr or cory_hrt@yahoo.com
thanx




MAKIN A NEW THREAD WITH PRICES... http://www.exriders.com/vbb/showthread.php?s=&threadid=265494

[fireburns99]

would you be willing to part out the top end only? I'm figureing a no, but its worth a shot.

[400EX QUADER]

naw...

[400EX QUADER]

MIGHT trade for a different R motor... not stock cylinder though.

[SuperChris]

How about a FRESH PRO-X 265 motor?

[400EX QUADER]

naw... This thing is fresh too remember.

[400EX QUADER]

I was gone for a couple of days... ttt

[400EX QUADER]

taking good offers..

[sleepinR]

would you be willing to part out with just the exhaust? and k&N filter?

[LT250Racer609]

will you take a grand for the motor before shipping

[400EX QUADER]

no thanx..

[400EX QUADER]

been a few days... ttt

[TANNER250r]

will you sell just the bottom end and if not how much do you want for the whole motor pm me

[doc-bones]

I will give you $500.00 for cylinder, spacerplate and head.

[dunenfool]

would you take $1400 plus shipping I'm in Nor Cal? My brother in laws wife needs the top end but we will take the whole thing. you can keep the pipe and carb, filter we already have those.

[400EX QUADER]

I'm leavin pretty soon... I'll pm people this evening.
thanx

[400EX QUADER]

ttt

[kustomfab2003]

I thought that you were trying to get a 310 or 330 non powervalve jug before. I have a ESR and A CT if you are interested.

Josh

[400EX QUADER]

now i'm lookin for a 350-400cc set-up for dragracing...

[kustomfab2003]

I have seen a few that have used a Honda pilot water cooled 400 or 430 topend on the 250R lower end. There is a guy selling the whole quad on ebay right now that you might be able to get info from. I'm looking to get a PV motor/topend for my R to run around Glamis on, but don't have the $$ to go new or buy a whole motor.

Good Luck,

Josh

[400EX QUADER]

bump

[400EX QUADER]

ttt

[2StrokeGod]

Would you sell just top end if so pm me.

[oldsking86]

Any luck with the motor, is it still forsale?

[400EX QUADER]

pm sent...

[oldsking86]

Your box is full, I tried to send you a pm back.. clear it out and I could send you it back.

[400EX QUADER]

I knew it was close... gimme a min.